micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 64

Page: 64 / 84

MINIMUM FLOW:

Enter a minimum flow rate of 10.0 lbs.

per minute (5.0 kg per

minute) of NH3. This

will prevent the system

from applying below

the recommended minimum rate for the

Micro-Trak NH3 flowmeter.

In NH3 mode, the console calculates rates and totals in lbs.

(kg) of nitrogen (N) or anhydrous ammonia (NH3) as shown

below.

Calibration Factors for NH3

To enter standard calibration mode, put the switch in the

MASTER HOLD position and press the CAL button for 1

second. Some of the calibration factors are the same as a

liquid system, but there are some important differences:

lbs. (kg) NH3 (scale tickets are in

NH3 for easy comparison)

lbs. (kg) NH3/Minute

lbs. (kg) NH3

remaining in tank
lbs. (kg) N per acre /(hectare)

provides application rate of

actual nitrogen

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

INLINE

BYPASS

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

CAL

CONT

SEL

RESET

TANK

___

HOLD

FLOW CAL:

This po si tion is used to cal i brate the flow me-

ter for ac cu rate liquid

mea

sure

ment. The

flowmeter has been

calibrated at the factory

to read in pounds of actual “N”.

ADJUST RATE:

Enter the desired amount of change in pounds

(kg) of actual “N” applied per acre (hectare)

for on-the-go adjustments to the Target

Rate when operating in AUTOmatic mode.

Enter 0 to disable this

feature.

ADJUST

RATE

TANK

MIN

FLOW

VOLUME /

MINUTE

FLOW

CAL

VOLUME

(1) (2) (3)

TARGET RATE:

Use the “+” and “-” buttons to

enter the desired application rate in pounds

(kg) of actual “N” applied per acre (hectare).

TARGET

RATE

Your Micro-Trak NH3 flowmeter has been tested at the factory

and assigned a “FLOW CAL” value (pulses/lb N) to make it

operate properly with the MT-3405D console. This number

is stamped on the metal tag attached to the flowmeter.

See Illustration below.

This is a starting point only. The value

must be fine tuned.

See Fine-Tuning Flowmeter Calibration

for NH3 on page 68.

When entering the flow cal value, take

note of decimal point placement.

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

MT-3405D Console Functions in NH3 Mode

(cont)

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands