micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 65

Page: 65 / 84

WIDTH:

To calibrate the implement width the nurse tank

must NOT be connected

to the system.

Turn on

Boom 1 switch and put

the RUN/HOLD switch

in RUN. Use the “+” and “-” switches to adjust

the number to the working width of your tool

bar in inches (thousandths of meters).

SETTING TOOL BAR WIDTH:

In order to accurately

measure the pounds (kg) of “N” applied per acre (hectare), it

is important to determine the correct “working” width. The

“working” width is the width of ground being affected by

any operation. This should be measured to the nearest inch

(millimeter).
Your “working” width will be the number of knives times the

knife spacing in inches (meters). For example, if you have 8

knives spaced at 30 inches, the working width is 240 inches.

See Illustration below.

Working width

WIDTH

CAL

AREA

(1) (2) (3)

SPEED CAL:

This position is used to calibrate the speed

sensor for ac cu rate speed and dis tance measurement. When

this position is selected,

the display will show

the SPEED CAL value

along with “CAL” on

the display.

See Speed

Calibration section (page 29) for details.

fine-tune the SPEED CAL, see Fine Tuning SPEED CAL for

NH3 on page 67.

SPEED

CAL

DISTANCE

INLINE/BYPASS:

Set to BYPASS (harness reverses the wires

so the servo will run correctly).

NOTE: If used

on a Micro-Trak NH3 system, it must be set

to Bypass.

INLINE

BYPASS

AREA /

HOUR

EXITING CALIBRATION:

To save the changes you made,

you MUST exit calibration by pressing and holding the CAL

button until the CAL icon disappears and the warning light

turns off.

TEST SPEED:

NOT USED

for anhydrous ammonia

application.

TEST

SPEED

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

Calibration Factors for NH3

(cont)

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands