micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 17

Page: 17 / 84

Select a mounting location which seems most workable, and

that best fits your needs. It should be con ve nient to reach

and high ly vis i ble to the op er a tor.

DO NOT IN STALL IN A

PO SI TION THAT OB STRUCTS THE VIEW OF THE ROAD

OR WORK AREA.

Whenever pos si ble, avoid lo ca tions that

expose the con sole to direct sun light, high tem per a ture,

strong chemicals or rain.
Place the mounting bracket in the selected lo ca tion, mark

holes, drill 1/4” (7mm) holes and mount bracket with bolts,

lock wash ers and nuts pro vid ed. (If bolts are not practical, use

self-tapping screws.)

See Illustration to the right.

Insert the console in the “U” bracket and install the console

knobs through the bracket, placing a rubber washer over the

threaded stud. Position console to proper viewing angle and

tighten the knobs securely.

Electrical Installation

The MT-3405D must be connected to a 12-volt DC

elec tri cal system. Power is connected directly to the battery.

The MT-3405D has an ON/OFF switch on the console to turn

the power off when the system is not being used.
Locate the power cable harness and connect to the mating

connector on the console. Connect the blue chassis ground

wire to a good frame ground.

See Il lus tra tion to the right.

Make sure there is good metal-to-metal contact. Route the

power cable from the console to the battery. Cut off excess

length. In routing cable to battery, avoid ar eas where the

ca ble may be subjected to abra sion or ex ces sive heat.

Install the in-line fuse provided with the kit on the white

wire, as illustrated, to protect the circuit.

Connect the ORANGE wire (hot) to the positive battery

terminal. At tach the BLACK wire (ground) to a screw or bolt

on the equipment frame.

See Il lus tra tion to the right.

sure there is good metal-to-metal con tact.
Your MT-3405D is equipped with a non-volatile elec tronic

mem o ry which does not re quire a con stant supply of

pow er to re tain daily totals or calibration val ues. The

advantage with this type of memory is that it conserves

battery power and will not dis charge the vehicle’s battery

when equipment is not in use.

Installation

Mounting the Display Console

Hot

(ORANGE)

10-Amp In-line

Fuse Required

Ground

(Blue)

+12 VDC

(RED)

NOTE: For negative ground systems only.

Tools Needed to Install the MT-3405D

•

Screwdrivers

•

Pliers

•

Set of Wrenches

•

Wire Cutter

•

Electric Drill and Bits

•

Hammer

•

Center Punch

•

12-Volt Test Light

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands