micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 62

Page: 62 / 84

Locate the 1/2” EVA vapor hose supplied with the kit.

Starting on one half of the tool bar, connect the 1/2” hose

to the outside steel vapor tube. Route the hose up the shank

and along the tool bar frame to the inside steel vapor tube.

Allow enough extra hose to avoid kinking at hinge points.

Cut the hose to length and attach to the inside steel vapor

tube. Install a 1/2” x 3/4” x 1/2” tee fitting approximately

halfway along this hose between the outside and inside

steel vapor tubes.

See Illustration below.

Repeat the same

procedure for the steel vapor tubes on the other half of the

tool bar. Secure all hoses with properly sized hose clamps.

Secure the hoses to the tool bar frame with cable ties.
Locate the 3/4” EVA hose supplied with the kit. Connect to

one of the 1/2” x 3/4” x 1/2” tee fittings and route along the

tool bar frame to other 1/2” x 3/4” x 1/2” tee fitting. Cut to

length and install on the tee fitting. Allow enough extra hose

to avoid kinking at hinge points. Now install a 3/4” x 3/4” x

3/4” tee fitting approximately halfway along this hose (center

of the tool bar) between the other two tee fittings. Using an

appropriate length 3/4” hose, connect this tee fitting to the

vapor tube connection on the NH3500 plumbing panel.

Secure all hoses with properly sized hose clamps. Secure

the hoses to the tool bar frame with cable ties.

NH3500 Kit - Vapor Line Installation

Electrical Connections

The main wiring harness is made specifically for use on

anhydrous ammonia applicators. The harness combines

the wires for the servo valve, flowmeter, shut-off valve

and remote access speed connector into a single 10-pin

connector.

PROCEDURE:

Plug the 10-pin tower of the main harness onto the main

plumbing panel harness. Use 15’ M/P extension cable

(provided) if necessary. Optional extension cables are

available.

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

NH3500 Vapor Tube Installation

FOR ALL NH3 KITS

Weld the steel vapor

tubes to the back of

your liquid tubes. All

electronic equipment,

including the console and

radar speed sensor,

MUST

BE DISCONNECTED

BEFORE WELDING ON

EQUIPMENT.

The four

steel vapor tubes should

be evenly spaced across

the applicator (two per

side) and installed so that only their wear resistant surface

contacts the soil. Mount the tubes just high enough to avoid

plugging.

VAPOR TUBES

WEAR RESISTANT

SURFACE

GROUND LEVEL

½” Vapor Hose

Breakaway

Coupler

NH3500 Kit

Steel Vapor Tubes

½” Vapor Hose

Manifold

½” Vapor Hose

¾” Vapor Hose

½” X ½” X ¾” Tee

¾” Tee

½” X ¾” X ½” Tee

Steel Vapor Tubes

¾” Vapor Hose

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands