micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 54

Page: 54 / 84

Appendix E

(cont)

Pump Driver (EPD) Module

The Electric Pump Driver (EPD) replaces the servo valve.

System flow is controlled by regulating the pump speed.

MODULE INSTALLATION NOTE:

The mounting surface

must be cleaned so it is free from dirt, moisture and oil

residues. Failure to clean the mounting surface may result in

the EPD working loose.

Remove the GREEN backing from the Dual-Lock

™

fasteners

on the bottom of the EPD unit. Position the EPD where

wiring will work the best. (A clean surface is desirable.)

Extension cables are available. Firmly press the EPD into

place. Secure the EPD to the equipment using plastic cable

ties to prevent the EPD from coming into contact with

moving parts if the Dual-Lock

™

fasteners should work loose.

If desired, the EPD can be fastened with screws, using the

holes in the mounting flanges.

ELECTRICAL INSTALLATION

This section explains how to connect your EPD to a 12-volt

power source, and how to connect your EPD to your

MT-3405D harness.

Note: The EPD must be connected to a 12-volt DC negative

ground electrical system.

BATTERY POWER CONNECTION

Locate the power cable, P/N 14499 and route to the battery.

In routing cable avoid areas where the cable may be

subject to abrasion or excessive heat. Attach the BLACK

wire (ground) to a screw or bolt on the equipment frame.

See Illustration to the upper right. Be sure there is a good

metal-to-metal contact. Connect the ORANGE wire to the

positive battery terminal.
Connect the power to the EPD by plugging the 3-pin W/P

tower on the power cable into the 3-pin W/P shroud of the

EPD module.
Locate the brown boom wire, P/N 14500. Plug the 2-pin W/P

shroud into the mating connector on the EPD module and

plug the quick-disconnect into the mating connector on the

“Boom 1” wire on the MT-3405D harness.

NOTE: be sure to route cables away from sharp edges,

areas of high heat and moving parts. Secure all cables

firmly with plastic cable ties.

Locate the servo cable. Connect the 3-pin W/P shroud to

the 3-pin W/P tower on the EPD module. Connect the other

end of the cable to the mating connector on the MT-3405D

harness.
Locate the pump cable P/N 14501. Plug the 2-pin W/P

tower into the 2-pin W/P shroud on the EPD module. A

mating connector is supplied to connect to the motor, or

the connector on the pump cable can be removed and wire-

to-wire connection can be made. Insure that the pump is

running in the correct direction. If not, simply reverse the

wires from the pump to the pump cable.

Hot

(ORANGE)

30-Amp In-line

Fuse Required

Ground

(Black)

+12 VDC

(White)

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands