micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 61

Page: 61 / 84

PRE-INSTALLATION:

Remove the Liquifier plumbing panel from the shipping

board. The Liquifier plumbing panel has been packaged

with the “strainer end” mounting bracket in a shipping

position. Before installing the unit on your applicator, move

this bracket to the other side (inlet side) of the strainer to

allow access to strainer clean-out plug for cleaning. After

repositioning bracket, make sure all three brackets rest on

a flat surface. If necessary, loosen all six carriage bolts (two

per bracket) at base of brackets to allow all brackets to rest

flat on mounting surface of tool bar. Tighten carriage bolts

only after insuring that all three brackets rest on bar and unit

does not “teeter” on center bracket.

LIQUIFIER KIT INSTALLATION

Remove any existing metering valves. If the old metering

valve has a built-in manifold, it is recommended to install

a separate new manifold for the Liquifier kit. Another

option, although not recommended, is to use the existing

manifold, making certain the old metering valve is in the

maximum open position to allow for minimal restriction

of flow through the plumbing. There should not be any

positive shut-off valves installed in the plumbing between

the Liquifier kit shut-off valve and the knives.

Install the plumbing panel on the tool bar frame using

the carriage bolts and flange lock nuts through the top

and bottom brackets of the system. Trim any excess

length off the bolts if required. Attach the hose from the

breakaway coupler to the strainer inlet. Check for proper

hose length for operation of the disconnect mechanism of

the breakaway coupler. Connect the manifold hose to the

servo valve outlet. Check for proper hose length to avoid

kinking at the hinge points.

LIQUIFIER VAPOR TUBE INSTALLATION

Locate the 1/2” EVA vapor hose supplied with the kit.

Starting on one half of the tool bar, connect the 1/2” hose to

the outside steel vapor tube. Route the hose up the shank

and along the tool bar frame to the inside steel vapor tube.

Allow enough extra hose to avoid kinking at the hinge points.

Cut the hose to length and attach to inside steel vapor tube.

Install a 11/2” x 3/4” x 1/2” tee fitting approximately half

way along this hose between outside and inside steel vapor

tubes.

See Illustration below.

Locate the 3/4” EVA hose supplied with the kit. Connect

one end to the 1/2” x 3/4” x 1/2” tee fittings and route along

the tool bar frame to the vapor outlet connections on the

Liquifier.

See Illustration below.

Allow enough extra

hose to avoid kinking at hinge points. Secure all hoses with

properly sized hose clamps. Secure the hoses to the tool bar

frame with cable ties.

INSTALLATION NOTE: It is recommended to use an NH3

compatible thread sealing compound on all pipe thread

fittings.

SERVO VALVE

COUPLER

KZ VALVE

FLOW METER

VAPOR OUTLETS

HEAT EXCHANGER

TUBING

STRAINER

MOUNT BRACKET

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

Liquifier Installation

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands