micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 74

Page: 74 / 84

Appendix J

Replacement Parts List

When ordering parts, please list the model number of your console, and the description and part number of each part that you want to order.

Part Number Description

12069

Magnet kit (6 magnets per kit)

10013

Speed sensor mount bracket

12910

14” Black plastic cable ties (bag of 10)

13774

Console Mount Kit*

10423

Console Mount Knob

10470

Console Mount Washer

14318

Power and Boom Console Harness

14324

Bulkhead Speed Cable (36”)

14793

Run/Hold Adapter Cable

10899

FM750N Flowmeter, NH3 Only

14958

NH3500 Servo

14959

Liquifier Servo

17136

1” Flanged Servo

17140

1-1/2” Flanged Servo

21353

NH3 Servo Gear-head Assembly

17316 Parallel Branch Adapter Kit

14348

FM1500N Flowmeter, NH3 Only/Liquifier

14320

Flow, Servo, Run/Hold and Relief Harness (120”)

17148

MT-3405D Ch2 Liquid Branch Harness (120”) (Boom 120”, Power Harness 240”)

13096

5-foot Hall-effect Speed/Flow Sensor Cable with threaded sensor, nut and female connector

ailing

hipping

ddress

Micro-Trak Systems, Inc.

P .O. Box 99

•

111 East LeRay Avenue

Eagle Lake, MN 56024-0099

The following replacement parts are available from your dealer

or distributor. To find your nearest dealer or distributor, visit

www.micro-trak.com or call Micro-Trak at 800-328-9613.

Optional 2-Pin, 3-Pin and 10-Pin Metri-Pack 150 extension cables:

*The Console Mount Kit is available only as a kit, some parts are not available in individual components.

Parts and design specifications subject to change without notice.

Part Number Description

13226

5-foot Remote Run/Hold Sensor Cable

01531

Speed Sensor kit (Magnetic)

14928

1” M-T Electric Servo Valve (Liquid)

11501

FM750 GFN Flowmeter

10131

FM750 SS Flowmeter

12274

FM1500 SS Flowmeter

17290

Reference Manual

13187

FM1000 SS Flowmeter

13269

FM500 Flowmeter

14286

FM270 Flowmeter

14829

FM10-100 Flowmeter

14366

NH3 System Main Harness (Ch1)

17184 Channel 2 Liquid Harness Kit (240”)

17165

MT-3405D Ch2 Remote Speed Adapter

14319

Boom Branch Cable (120”)

Part No. M/P 2-Pin Part No. M/P 3-Pin

Part No. M/P 7-Pin Part No.

M/P 10-Pin

Part No. W/P 3-Pin

13200

5-Foot

13205

5-Foot

14146

5-Foot

13220

5-Foot

10450

5-Foot

13201

10-foot

13206

10-foot

14147

10-foot

13221

10-foot

10449

10-foot

13202

15-foot

13207

15-foot

14103

15-foot

13222

15-foot

10876

15-foot

13203

20-foot

13208

20-foot

14236

20-foot

13223

20-foot

10829

20-foot

13204

25-foot

13209

25-foot

14237

25-foot

13224

25-foot

11462

25-foot

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands