micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 31

Page: 31 / 84

The

“Special” Calibration Mode

is used to set up system

parameters that rarely need to be changed or adjusted. To

enter Special Cal, put the system in MASTER HOLD, turn

the console OFF, press and hold both the CONT SEL button

and CAL button while turning console ON. The console will

display SPEC for 2 seconds to show that the console is in the

Special Calibration mode.

Calibration Values-Channel 1,2

The following table describes the special cal parameters and

shows the factory settings. More detailed descriptions follow

the table.

NOTE: Each channel has its own independent special-cal

parameters.

“Special” Calibration

Release the CONT SEL and CAL buttons. The CAL icon and

Warn LED will turn on. The desired Special Calibration

parameter(s) can then be accessed with the rotary switch per

the illustration below. To exit Special Calibration, press and

hold the CAL button for 2 seconds. The console will store any

changes and revert to normal operation.

NOTE: you must

exit Special Calibration to save changes.

Special Cal

Fill Tank Size

Units... and...

Valve Voltage

Material

Valve Response Speed

Tank Set Point

Auto Shutoff

On/Off

Auto Delay Time

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

INLINE

BYPASS

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

CAL

CONT

SEL

RESET

TANK

___

HOLD

Ch2: Operating Mode

Special Cal

Parameter

Description

Factory Setting

Ch1: Units

(same for both Ch1, Ch2)

System of units: EnG (English) / mEt (Metric) /TurF (Turf)

EnG (English)

Ch2: Operating Mode

Ch2: Operating Mode: norm (Normal), InJ (Injection), PAr (Parallel)

Ch2: norm (Normal)

Valve Voltage

Servo Valve Drive Voltage (8/12)

Material

Choose Liquid (H2O or Anhydrous (NH3)

H2O

Valve Response Speed

Set Valve Response (-4 to 3)

-1

Auto Delay Time

Delay servo response when going from Hold to Run (Off) to 4 sec.)

- Allows slow shutoff valves TIME to open before servo starts moving

Auto Shutoff

Runs servo toward minimum when in hold (On/Off)

Off

Tank (Low) Set Point

Sets alarm point if using Tank Function (Off or 1-65,535)

Off

Fill Tank Size

Size (volume) of Full Tank (Off or 1-65,535)

Off

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands