background image

17

Delivery, transport and setting up

3.  

 Delivery,   transport and   setting up

3.1 Safety 

regulations

Warning!

You may get your hands or feet squashed when transporting 

and installing the appliance. Wear protective gloves and 

safety boots.

Warning!

Because of the heavy weight of the appliance, you could injure 

yourself if you try to lift it. To  carry appliances of the sizes 30 and 

55, at least two persons, for appliances of the sizes 75 and 110, four 

people are needed. Appliances larger than that may not be carried 

but must be transported with a manual pallet jack or forklift truck.

                 

30

55

75

110

160

260

450

750

  

         

Warning!

The appliance could fall over and seriously injure you. Never tilt the 

appliance and transport it in upright position only. 

3.2  

Delivery

The appliance is packed in cardboard and is delivered on a wooden palette.

3.3  

Transport

The appliance can be transported in three ways:

 

With a  forklift truck; move the forks of the truck entirely under the pallet

 

On a manual pallet jack

 

On its own castors, in case of the corresponding configuration, for which the catch on the 

(front) castors must be released

3.4  

Unpacking

To avoid damage, do not unpack the appliance until you reach the installation site.

Remove the cardboard packaging by pulling it upwards or carefully cutting along an edge. 

3.4.1  Checking for completeness and  transport damage

 

Check the delivery note to ensure that the delivery is complete.

 

Check the appliance for damage. 

If you notice deviations from the delivery note, damage or irregularities, do not put the 

appliance into operation but inform the haulage company and the manufacturer.

3.4.2 Disposing of  

 packaging material

Dispose of the packaging material (cardboard, wood, foil) in accordance with the applicable 

disposal regulations for the respective material in your country.

Summary of Contents for IF 110 PLUS





























































Reviews: