Meatest M631 Operation Manual Download Page 51 | Manualshive

Page: 51 / 70

background image

M631 Precision RTD Simulator

MEATEST

51

Operation manual

[:SOURce]:UFUNction:CURVe:PRESet:SAVE

Syntax:

[:SOURce]:UFUNction:CURVe:PRESet:SAVE

Description:

This command saves current curve to non-volatile memory. Unsaved changes will
disappear on restart, function change or selection of another curve.

Parameters:

None

Remarks:

Overlapped command

Example:

UFUN:CURV:PRES:SAVE

[:SOURce]:UFUNction:CURVe:PRESet:UNIT

Syntax:

[:SOURce]:UFUNction:CURVe:PRESet:UNIT <SPD>

[:SOURce]:UFUNction:CURVe:PRESet:UNIT?

Description:

This command sets / retrieves unit of selected curve. Data will be saved to non-volatile
memory on UFUN:CURV:PRES:SAVE command.

Parameters:

<SPD>

Quoted user function unit. Upper alpha, lower alpha, digits and spaces
are allowable. Maximum string size is 2 characters.

Remarks:

Overlapped command

Example:

UFUN:CURV:PRES:UNIT "N"

UFUN:CURV:PRES:UNIT? Response: "N"

:STATus:OPERation:CONDition

Syntax:

:STATus:OPERation:CONDition?

Description:

This  query  returns  the  content  of  Operational  Condition  register.  It  is  a  decimal  value
which  corresponds  to  the  binary-weighted  sum  of  all bits  in  the  register.  Register  is  not
cleared  after  this  query. The  response to the  query therefore  represents  an  instantaneous
'Snapshot' of the register state, at the time that the query was accepted.

Parameters:

<DNPD>

Operational Condition register

Remarks:

Overlapped command

Example:

STAT:OPER:COND? Response: 2

«
...
49
50
51
52
53
...
»

Summary of Contents for M631







































































Reviews:

No comments

Related manuals for M631

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands