Meatest M631 Operation Manual Download Page 5 | Manualshive

Page: 5 / 70

background image

M631 Precision RTD Simulator

MEATEST

5

Operation manual

1.

Basic information

Precision RTD Simulator M631 is suitable for automated simulation of different resistance

sensors (temperature, pressure, position, force …). Internal design eliminates “zero resistance effect”
which is typical for most resistance decades.

Resistance value is created via appropriate combination of physical resistors. RTD simulator is

equipped  with  built-in  function  of  direct  simulation  of  most  frequent  temperature  Pt  and  Ni  sensors.
Low thermal voltage relays and stable resistors are used as main parts of the RTD Simulator. Actual
set  values  are  displayed  high  resolution  TFT  display. M631  is sophisticated  instrument  with its  own
re-calibration  procedure.  The  procedure  enables  to  correct  any  deviation  in  resistance  without  any
mechanical adjustment.

Instrument is especially suitable for automatic testing procedures. RS232 line (optionally

IEEE488, USB and Ethernet bus) is used for connecting RTD simulator to the computer.

2.

Preparation for use

2.1.

Inspecting package contents, selecting the installation location

Basic package includes the following items:



RTD Simulator M631



RS232 cable



CD with demo program



User’s manual



Test report

The instrument must be powered by 230/115 V – 50/60 Hz mains. Before powering on the

instruments, place it on a level surface. If the instrument was stored out of range of reference
temperatures, let it stabilize for one hour.

2.2.

Power on



Before connecting the instrument to the mains, check the position of the mains voltage selector
located at the rear panel.



Plug one end of the power cord into the connector located at the rear panel and connect the other
end of the power cord into a wall outlet.



Switch on the mains switch located at the rear panel. Display is lit.

«
...
3
4
5
6
7
...
»

Summary of Contents for M631







































































Reviews:

No comments

Related manuals for M631

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands