Meatest M631 Operation Manual Download Page 39

Page: 39 / 70

M631 Precision RTD Simulator

MEATEST

Operation manual

:CALibration:SECure:PASSword

Syntax:

:CALibration:SECure:PASSword <DNPD>

Description:

This command validates entered password and enables calibration access if verification is
successful. Access is invalidated after reset or if CAL:SEC:EXIT command is issued.
Calibration password can be changed from simulator system menu

SETUP->Calibration-

>Change password.

Parameters:

<DNPD>

Range 0 ... 4294967295 (default 0)

Remarks:

Overlapped command

Example:

CAL:SEC:PASS 0

:CALibration:SECure:EXIT

Syntax:

:CALibration:SECure:EXIT

Description:

This command exits calibration mode and access.

Parameters:

None

Remarks:

Overlapped command

Example:

CAL:SEC:EXIT

:DISPlay:ANNotation:CLOCk:DATE:FORMat

Syntax:

:DISPlay:ANNotation:CLOCk:DATE:FORMat <CPD>

:DISPlay:ANNotation:CLOCk:DATE:FORMat?

Description:

This command sets format of date displayed on device screen.

Parameters:

<CPD>

{MDYS|MDYA|DMYS|DMYO|DMYA|YMDS|YMDO} (default MDYS)

·MDYS

M/D/Y format

(M-month, D-day, Y-year)

·MDYA

M-D-Y format

·DMYS

D/M/Y format

·DMYO

D.M.Y format

·DMYA

D-M-Y format

·YMDS

Y/M/D format

·YMDO

Y.M.D format

Remarks:

Overlapped command

Value is not affected by reset or by *RST command

Example:

DISP:ANN:CLOC:DATE:FORM MDYS

DISP:ANN:CLOC:DATE:FORM? Response: MDYS

Summary of Contents for M631







































































Search results

Summary of Contents for M631

Reviews:

Related manuals for M631

Brands by name

Popular brands

Meatest M631, Operation Manual

Search results

Summary of Contents for M631

Reviews:

Related manuals for M631

Brands by name

Popular brands