Meatest M631 Operation Manual Download Page 40

Page: 40 / 70

MEATEST

M631 Precision RTD Simulator

Operation manual

:DISPlay:ANNotation:CLOCk[:STATe]

Syntax:

:DISPlay:ANNotation:CLOCk[:STATe] <BOOL>

:DISPlay:ANNotation:CLOCk[:STATe]?

Description:

This command enables/disables showing actual time in title on device screen

Parameters:

<BOOL>

{ON|OFF|1|0} (default 1)

·ON

actual time is shown

·OFF

actual time is hidden

·1

same as ON

·0

same as OFF

Remarks:

Overlapped command

Value is not affected by reset or by *RST command

Example:

DISP:ANN:CLOC ON

DISP:ANN:CLOC? Response: 1

:DISPlay:BRIGhtness

Syntax:

:DISPlay:BRIGhtness <DNPD>

:DISPlay:BRIGhtness?

Description:

This command sets brightness of device display.

Parameters:

<DNPD>

Range 0.0 ... 1.0 (default 1.0), 0.0 – Min, 1.0 – Max brightness

Remarks:

Overlapped command

Value is not affected by reset or by *RST command

Example:

DISP:BRIG 1.0

DISP:BRIG? Response: 1.00

:DISPlay:LANGuage

Syntax:

:DISPlay:LANGuage <CPD>

:DISPlay:LANGuage?

Description:

This command sets language that is used on device display.

Parameters:

<CPD>

{ENGLish|DEUTsch|FRENch|RUSSian|SPANish|CZECh}
(default ENGL)

·ENGLish

english version

·DEUTsch

german version

·FRENch

french version

·RUSSian

russian version

·SPANish

spanish version

·CZECh

czech version

Remarks:

Overlapped command

Value is not affected by reset or by *RST command

Example:

DISP:LANG ENGL

DISP:LANG? Response: ENGL

:OUTPut:SHORt

Syntax:

Summary of Contents for M631







































































Search results

Summary of Contents for M631

Reviews:

Related manuals for M631

Brands by name

Popular brands

Meatest M631, Operation Manual

Search results

Summary of Contents for M631

Reviews:

Related manuals for M631

Brands by name

Popular brands