Meatest M631 Operation Manual Download Page 10

Page: 10 / 70

MEATEST

M631 Precision RTD Simulator

Operation manual

Operation

4.1.

Connection and disconnection of output terminals

Set value is connected (disconnected) to the output terminals after pressing OPER key.

Connected output terminals are indicated by the lit LED in the key.

Disconnected output terminals can be used for “Open terminals” simulation. “Short circuit” is

simulated after pressing SHORT key. Active SHORT key (LED in the key is ON) replaces the main
value with the short circuit. Also the short circuit must be connected to the output terminals by the
OPER key.

4.2.

Wires connection

Output resistance is available on R output terminals. Available is 2, 3 and 4-wire connection.

Both sides (red and grey) are floating up to 500Vpk against the case (PE).

Ground terminal is connected to the metal case and to the protective earth (PE).

4.3.

Setting the function

Function can be changed after pressing „Function“ softkey. New function is selected using

cursor keys ▲,▼ or display softkeys. Selection must be confirmed by pressing SELECT key or „OK“
softkey.

Device supports following functions:

Resistance

Offers direct setting of exact resistance value.

Figure 5 Resistance screen

Editable parameters:

Resistance value:

16 Ω … 400 kΩ

Switching mode:

FAST, SMOOTH, VIA OPEN, VIA SHORT

Summary of Contents for M631







































































Search results

Summary of Contents for M631

Reviews:

Brands by name

Popular brands

Meatest M631, Operation Manual

Search results

Summary of Contents for M631

Reviews:

Brands by name

Popular brands