manualshive.com logo in svg

Meatest M631, Operation Manual

Share
Download
Meatest M631 Operation Manual Download Page 20

MEATEST 

M631 Precision RTD Simulator

 

Operation manual 

20 

SHORT value is lower than min (R1, R2). 
 

Platinum standard 

Platinum thermometers can be simulated according to the different standards. Available standards are: 

PT385 (68) 

DIN, standard EN60751, temperature scale IPTS68 
(A=3.90802e-3, B=-5.80195e-7, C=-4.2735e-12) 

PT385 (90) 

DIN, standard EN60751, temperature scale ITS90 
(A=3.9083e-3, B=-5.775e-7, C=-4.18301e-12) 

PT3916 

Pt3916 temperature curve 

 

(A=3.9692e-3, B=-5.8495e-7, C=-4.2325e-12) 

PT3926 

Pt3926 temperature curve 

 

(A=3.9848e-3, B=-5.870e-7, C=-4.0e-12) 

PT User 

user defined temperature curve 

 

(A=3.9083e-3, B=-5.775e-7, C=-4.18301e-12) – values can be changed 

 
Platinum user coefficients 

This menu permits A, B and C coefficients definition of the PT User platinum standard (see above). 

 
Timings 

This menu permits definition of different time dependent resistance curves. Each curve is defined by 
the  Timing  table.  Each  row  in the  table  contains information  about  resistance  value  and  duration  for 
which is this value applied. If the timing function is activated all rows are sequentially executed. User 
can define more timing tables with different names. Number of sequences is limited to 64. 

 
User function curve 

This  menu  permits  definition  of  different  conversion  curves.  Each  curve  is  defined  by  the  Lookup 
table.  Each  row  in  the  table  contains  information  about  value  of  simulated  function  and  appropriate 
resistance  value.  User  can  define  more  lookup  tables  with  different  names.  Typical  application  is 
definition table for simulation of non-standard resistance thermometers. Number of conversion curves 
is limited to 64. 

 
 

System 

This menu permits setting system parameters of device. 

Language 

Language setting. 

Backlight 

Display backlight level setting. 

Beeper volume 

Beeper volume level setting. 

Keyboard beep 

Enables / Disables keyboard beep. 

Time 

Internal time setting. 

Date 

Internal date setting 

 
 

Interface 

This menu permits setting parameters of remote control interfaces. 

Summary of Contents for M631







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands