manualshive.com logo in svg

Mazda 6 Facelift 2005, Training Manual, Page: 51 / 274

Share
Download
Mazda 6 Facelift 2005 Training Manual Download Page 51

Engine Diesel 

Engines 

• 

The different conditions of the oil dilution are shown in the following table. 

 

Item

Engine oil level

DPF indicator light

—

—

MIL

—

—

Output restriction

—

—

DTC stored in PCM

Customer action

—

—

DPF automatic regeneration

Dealer action

—

—

If DTC 253F is stored 

in the PCM, replace 

the engine oil even if 

the engine oil level is 

lower than the "X" 

mark on the oil 

dipstick.

After inspecting

engine oil level

replace the engine oil.

Bring the vehicle to a dealer

Disabled

Engine oil dilution

Enabled

P252F

Flashes every 0.4 s

 —

Max. 150 km/h (93 mph)

P253F

 

 

M6FL_01T011 

 

1 

F mark 

4 

Oil level okay 

2 

X mark 

5 

Oil level excessive 

3 Oil 

dipstick 

  

 

Service Training Mazda6 Facelift 

01-37 

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments