Mazda 6 Facelift 2005 Training Manual Download Page 140

Page: 140 / 274

G66M-R Transmission/Transaxle

Shift Interlock Mechanism

•

The shift interlock mechanism provides reliable double-engagement prevention.

•

During shifting, the shift rods, except for the one in operation, are locked in the neutral
position by the interlock sleeve.

Neutral Condition

•

The interlock sleeve fits into the notches of the 1st/2nd, 5th/6th and reverse shift forks.

•

The control lever fits into the notch of the 3rd/4th shift fork.

M6FL_05007

Shift fork

Control lever

2 Interlock

sleeve

05-12 Service

Training

Mazda6

Facelift

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Search results

Summary of Contents for 6 Facelift 2005

Reviews:

Related manuals for 6 Facelift 2005

Brands by name

Popular brands

Mazda 6 Facelift 2005, Training Manual

Search results

Summary of Contents for 6 Facelift 2005

Reviews:

Related manuals for 6 Facelift 2005

Brands by name

Popular brands