Mazda 6 Facelift 2005 Training Manual Download Page 60 | Manualshive

Page: 60 / 274

background image

Diesel Engines

Engine

Injectors

•

Solenoid valve-type injectors with lower power consumption and better response have
been introduced.

M6FL_01068

1

From common rail

3

To fuel tank

2 Connector

NOTE:

Since the size of the injector connector is relatively big compared to the diameter of

the injector head, there might be an interference between the connector and the
injector seal during removal and installation of the cylinder head cover. In order to
prevent any damage to the seal, wrap vinyl tape around the injector connector
covering the connector edges.

•

In addition, the leak-off lines of the injectors are located under the cylinder head cover.
As a result, the total leak-off amount of the injectors must be measured and compared to
the values of a known good vehicle in order to detect a leaking solenoid valve.

NOTE:

Always replace the gaskets of the injector leak-off lines when removing them. As the

leak-off lines are located under the cylinder head cover, fuel leaking from the lines
can contaminate the engine oil. This results in engine oil dilution and hence in engine
damage.

01-46

Service Training Mazda6 Facelift

«
...
58
59
60
61
62
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: JANE Pages: 21

Brand: Neuspeed Pages: 2

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Brand: Nuna Pages: 17

Electra 225 1965

Brand: Buick Pages: 914

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: Softride Pages: 4

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: Mercedes-Benz Pages: 296

Brand: Alphasonik Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands