manualshive.com logo in svg

Mazda 6 Facelift 2005, Training Manual, Page: 219 / 274

Share
Download
Mazda 6 Facelift 2005 Training Manual Download Page 219

Body & Accessories 

Accessories 

Steering Lock Unit 

• 

The steering lock unit consists of the steering lock and the start knob, which is blocked in 
OFF position. When the start knob is pushed in a request signal is sent by the keyless 
antennas. If the keyless control module successfully identifies a valid card key, the 
keyless indicator light illuminates green, and the ignition can be switched on. If for some 
reason the card key cannot be identified, or is not functioning, the start knob can be 
removed and the auxiliary key inserted to start the engine. 

Steering Lock Unit Structural View 

 

M6FL_09021

 

 

 

1 

Start knob 

3

 

Coil antenna 

2 

Steering lock unit 

 

 

 

Steering Lock Unit Programming 

• 

If the steering lock unit is replaced, the new unit must be programmed using WDS.  

 

NOTE:

  Do not program the steering lock while WDS or any other computer devices are in 

the vehicle. Make sure all card keys are operational and have good batteries. 

 

NOTE: 

To program the steering lock unit a registered card key is necessary. If there is no 
programmed card key, perform the steering lock unit programming after the card key 
programming. 

 
1.  Enter the vehicle with a registered card key. 

2.  Establish communication between WDS and the vehicle. 

3.  Select the option 

Toolbox

→

Body

→

Security

→

PATS Functions

. 

4.  Carry out the security access procedure (read out the WDS outcode, and input the 

corresponding incode). 

5.  Select the option Steering Lock Unit Programming and follow instructions on WDS to 

complete programming. 

 

Service Training Mazda6 Facelift 

09-37 

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments