Mazda 6 Facelift 2005 Training Manual Download Page 268 | Manualshive

Page: 268 / 274

background image

Accessories Body

&

Accessories

Front Seat Belt Warning Alarm

•

Driver seat belt warning alarm operates with a single buckle switch like the seat belt
warning alarm from the previous Mazda6.

•

The seat belt warning light in the instrument cluster shows if the driver is not buckled
while ignition is on or engine runs. An additional warning tone sounds when vehicle
speed exceeds 20 km/h.

•

Driver seat belt warning alarm chime can be switched off using WDS.

•

A front passenger seat belt warning alarm was added to Mazda6 Facelift, using an
occupancy sensor to detect whether the front passenger seat is occupied or not and a
buckle switch to indicate the buckle situation.

•

The warning light in the instrument cluster shows if the passenger is not buckled when
vehicle speed is higher than 20 km/h. Then also the warning sound occurs.

•

Passenger seat belt warning alarm chime can be switched off using WDS.

Front Seat Belt Warning Alarm Wiring Diagram

M6FL_09060

1 Instrument

cluster

3 Buckle switch (passenger´s side)

2

Buckle switch (driver´s side)

4

Occupancy sensor

09-86 Service

Training

Mazda6

Facelift

«
...
266
267
268
269
270
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Pacbrake Pages: 9

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

2012 Truck Chassis cab

Brand: RAM Pages: 506

Brand: Radical Sportscars Pages: 44

Brand: Oldsmobile Pages: 354

Brand: iDataLink Pages: 6

TOUR EASY 4 936550

Brand: Reimo Pages: 4

Brand: Westin Pages: 2

Directechs FORD11

Brand: Directed Pages: 23

PerfectView CRT300

Brand: Waeco Pages: 200

Quad Gear 18-029-010401-00-SC

Brand: Classic Accessories Pages: 4

Brand: Saab Pages: 9

Hyper Car Charger 30W

Brand: 3mk Pages: 6

Brand: Toyota Pages: 250

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands