manualshive.com logo in svg

Mazda 6 Facelift 2005, Training Manual, Page: 210 / 274

Share
Download
Mazda 6 Facelift 2005 Training Manual Download Page 210

Accessories Body 

& 

Accessories 

Advanced Keyless Engine Start Structural View 

 

 

M6FL_09016 

 

1 

ID verification Not OK 

7 

Steering lock unit 

2 

Keyless warning light (red) (flash) 8 

Transmitter 

(card 

key) 

3 

ID verification OK 

9 

Keyless antenna 

4 

Keyless indicator light (green) 
(illuminated) 

10 

Reception range (interior) 

5 Keyless 

receiver 

11 4SD 

6 Keyless 

control 

module 

12 5HB, 

WGN 

 
 

Operation in detail: 
 
a) 

The start knob is pressed. 

b) 

The request signal is sent by wire to the keyless control module. 

c) 

The keyless control module sends a signal through the antenna. 

d) 

The antenna sends a signal to the card key. 

e) 

The card key sends its ID to the keyless receiver. 

f) 

The keyless receiver forwards the ID to the keyless control module. 

 

The keyless control module checks the ID. 

g) 

If the ID is valid, the keyless control module sends a signal to the steering lock unit to 
unlock the steering lock. 

 
 

09-28 Service 

Training 

Mazda6 

Facelift 

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments