Mazda 6 Facelift 2005 Training Manual Download Page 190 | Manualshive

Page: 190 / 274

background image

Accessories Body

&

Accessories

BCM On-Board Diagnostic System

•

The on-board diagnostic system of the BCM consists of the following functions:

–

Constant monitor

–

Self test

–

PID monitor

Constant Monitor

•

The constant monitor is carried out whenever the ignition is ON. If a fault is detected, a
DTC will be stored in the BCM. When the ignition is switched off, DTCs stored by the
constant monitor will be deleted. The constant monitor only monitors the following
systems:

–

Rain sensor

–

Battery voltage

–

BCM IC (Integrated Circuit)

Self Test

•

All systems other than those tested in the constant monitor, are monitored during the
self-test. If a fault is detected, a DTC will be stored in the BCM.

•

The self-test function allows BCM DTCs to be displayed on WDS. To view these,
connect WDS to the vehicle and select the option

Toolbox

→

Self

Test

→

Modules

→

GEM

.

•

When the ignition is switched off, DTCs stored by the self-test will be deleted.

•

To conduct the self test, the following conditions must first be met:

–

Ignition switch ON

–

All switches other than ignition switch OFF

–

All doors, bonnet, trunk lid and liftgate are closed and unlocked

–

Parking brake is engaged

09-8 Service

Training

Mazda6

Facelift

«
...
188
189
190
191
192
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Subaru Pages: 21

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: WABCO Pages: 52

Brand: Park-Daddy Pages: 22

Brand: Whispbar Pages: 15

Ford 4” UNI-CAM

Brand: Nav TV Pages: 6

2007 9-3 Remote Starter

Brand: Saab Pages: 304

Brand: ACV Pages: 2

Brand: rough country Pages: 4

Brand: Volvo Pages: 197

Brand: Carbest Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands