Mazda 6 Facelift 2005 Training Manual Download Page 216 | Manualshive

Page: 216 / 274

background image

Accessories Body

&

Accessories

Erasing Registered Card Keys

1. Establish communication between WDS and the vehicle.

2. Select the option

Toolbox

→

Body

→

Security

→

PATS Functions

.

3. Carry out the security access procedure (read out the WDS outcode, and input the

corresponding incode).

4. Select the option Card Key Clearing.

5. Complete procedure by programming at least two new card keys.

Keyless Antennas

•

A total of six to seven (depending on the body style) antennas send request signals to
card keys, and relay card key ID’s to the keyless control module.

•

The keyless antennas built into the front doors can output signals to both inside or
outside the vehicle, and change the level of radio waves (output to inside or outside the
vehicle) depending on whether a card key is detected inside or outside the vehicle.

•

The signal received by the antenna with the strongest signal is used by the keyless
control module to identify the card key.

09-34 Service

Training

Mazda6

Facelift

«
...
214
215
216
217
218
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: iDataLink Pages: 30

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: Metra Electronics Pages: 2

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: Brodit Pages: 2

Brand: Cadillac Pages: 352

Powerbuilt 648601

Brand: AllTrade Pages: 3

SportQuest Series

Brand: Perrycraft Pages: 2

Brand: SkyRack Pages: 2

Brand: Rhino-Rack Pages: 5

Brand: Chipolino Pages: 11

Brand: Paser Pages: 10

Brand: E-Trailer Pages: 8

Brand: Ferrari Pages: 45

Brand: Metra Electronics Pages: 2

Brand: AA Products Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands