Mazda 6 Facelift 2005 Training Manual Download Page 233 | Manualshive

Page: 233 / 274

background image

Body & Accessories

Accessories

Theft Deterrent System

•

The theft deterrent system is standard equipment in Base and in Touring specification.

•

The theft-deterrent system includes sound and light alarm. The system will be armed by
locking the vehicle with the transmitter. The armed system alarms when the bonnet, the
trunk lid (4SD) or liftgate (5HB, WGN), or a door is opened by means other than the
transmitter. The turn lights flash and the horn and the theft-deterrent siren sound.

•

When the transmitter unlock button is pressed, the alarm stops. Also a successful engine
start stops the alarm.

•

An intruder sensor has been installed in the forward part of the roof (4SD, 5HB: without
sliding sunroof, WGN: with sliding sunroof) or in the center part of the roof (4SD, 5HB:
with sliding sunroof, WGN: without sliding sunroof). The intruder sensor senses
movement in the vehicle based on radio waves, and sends an alert signal to the theft-
deterrent control module.

•

A second intruder sensor has been installed in the rear part of the roof. (WGN)

•

A theft-deterrent siren has been installed on the rear, left side of the trunk. The theft-
deterrent siren includes an internal back-up power supply so that if power from the
battery is cut by any means, the siren will still sound.

Service Training Mazda6 Facelift

09-51

«
...
231
232
233
234
235
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Ranger design Pages: 6

Brand: UnderCover Pages: 16

Brand: Vauxhall Pages: 323

Brand: Porsche Pages: 192

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Brand: JKS Pages: 6

Brand: WABCO Pages: 34

Brand: AL-KO Pages: 40

Brand: AUTOTECH Pages: 4

Brand: Mazda Pages: 605

Brand: Truma Pages: 16

Brand: Valeo Pages: 29

Brand: XTC Pages: 2

Brand: Discount Car Stereo Pages: 5

Brand: Kuda Pages: 2

2012 Civic Hybrid

Brand: Honda Pages: 18

Brand: Kenwood Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands