Mazda 6 Facelift 2005 Training Manual Download Page 108 | Manualshive

Page: 108 / 274

background image

Diesel Engines

Engine

NOTE:

If the exhaust gas temperature during manual regeneration exceeds a certain limit,
the PCM stops the regeneration process and increases the engine speed to
2500 min

-1

to cool the DPF.

NOTE:

Depending on the amount of soot accumulated the PCM performs normal and long

regeneration mode one after another, i.e. the regeneration process may take up to
94 min. If the DPF indicator light does not extinguish after the manual regeneration is
finished, perform the regeneration process again.

Replacing the MAF Sensor

•

After replacing the MAF sensor, its adaptation values in the PCM must be reset with the
aid of the WDS. Therefore, select the option

Toolbox

Æ

Powertrain

Æ

Data Reset

Æ

MAF Sensor

.

Replacing the High-Pressure Pump

•

After replacing the high-pressure pump, its adaptation values in the PCM must be reset
with the aid of the WDS. Therefore, select the option

Toolbox

Æ

Powertrain

Æ

Data Reset

Æ

Fuel Pump

.

Replacing Injectors

•

After replacing one or more injectors, the following steps must be performed:

1. The injector adaptation values in the PCM must be reset using the option

Toolbox

Æ

Powertrain

Æ

Data Reset

Æ

Injector

.

2. The injector correction factors must be programmed into the PCM via the option

Toolbox

Æ

Module Programming

Æ

Programmable Parameters

Æ

Injector

Correction Factors

.

3. The injection amount learning function must be performed using the option

Toolbox

Æ

Powertrain

Æ

Engine Checks

Æ

Learning

Æ

Correction after Parts

Installation

.

01-94

Service Training Mazda6 Facelift

«
...
106
107
108
109
110
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Mazda Pages: 4

Brand: OEM Tools Pages: 4

Brand: Nav TV Pages: 3

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

autoSteady AS101

Brand: Enduro Pages: 48

Brand: Jeep Pages: 136

Brand: Prorack Pages: 10

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

Brand: Camoplast Pages: 19

Brand: Havis Pages: 5

Brand: Kia Pages: 680

Brand: Prorack Pages: 14

Brand: GROM Audio Pages: 20

transit connect 2012

Brand: Ford Pages: 299

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands