Mazda 6 Facelift 2005 Training Manual Download Page 265 | Manualshive

Page: 265 / 274

background image

Body & Accessories

Accessories

Rear Seat Belt Warning Alarm

•

The rear seat belt warning LEDs are installed on the installation area of the rear view
mirror.

•

The indicator and the buzzer are built-in corresponding to the seat belt for each rear
seat.

Operation

•

After the ignition switch is turned to the ON position, each indicator illuminates
continuously while the generator warning light is illuminating:

–

green when the seat belt is fastened (buckle switch is on)

–

red when the seat belt is not fastened (buckle switch is off)

•

Each indicator turns off if the condition corresponds to any of the following:

–

When the ignition switch is in the LOCK position.

–

When approx. 40 s have elapsed since the generator warning light turned off (engine
runs).

•

If the buckle switch signal changes (on to off, or off to on) with the ignition switch in the
ON position and the indicator is not illuminated, the corresponding seat belt indicator
illuminates.

•

In addition, when the buckle switch is changed from off to on (seat belt was unfastened),
the buzzer inside the rear seat belt reminder indicator sounds for approx. 0.5 sec to alert
the driver.

Service Training Mazda6 Facelift

09-83

«
...
263
264
265
266
267
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Vauxhall Pages: 199

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: Edelbrock Pages: 2

WrapAround Windjammer

Brand: Bestop Pages: 7

Brand: Toyota Pages: 371

Brand: Wilco Offroad Pages: 4

Brand: Parkeon Pages: 43

Brand: Pyle Pages: 2

Brand: Joie Pages: 53

2010 MX-5 Miata

Brand: Mazda Pages: 8

RAV-4 2015 Series

Brand: Toyota Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands