Mazda 6 Facelift 2005 Training Manual Download Page 211 | Manualshive

Page: 211 / 274

background image

Body & Accessories

Accessories

Customization

•

The following functions can be switched ON or OFF using WDS:

–

Out of range auto-lock function (set to OFF from factory).

–

Lock/unlock answer back function (set to OFF from factory).

–

Low card key battery warning (set to ON from factory).

Card Key

•

A thin, card type transmitter has been adopted.

•

The card key incorporates buttons to lock and unlock the doors and to disable the
intrusion sensor (when burglar alarm is fitted), a button type battery (CR2025), an
auxiliary key, and an indicator light.

•

When the LOCK or UNLOCK buttons are operated or a request signal is received from
the vehicle, the indicator light illuminates.

•

If the advanced keyless entry system is malfunctioning, the driver’s door can be opened
and the engine started using the auxiliary key.

•

A transponder is built into the auxiliary key for vehicles with immobilizer system.

•

Expected battery life for the card key is approximately one year.

Service Training Mazda6 Facelift

09-29

«
...
209
210
211
212
213
...
»

Summary of Contents for 6 Facelift 2005



















































































































































































































































































Reviews:

No comments

Related manuals for 6 Facelift 2005

Brand: Saab Pages: 3

Brand: Dometic Pages: 158

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Brand: Havis-Shields Pages: 1

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: Mercedes-Benz Pages: 296

Brand: Ford Pages: 585

Brand: Westin Pages: 3

Brand: Honda Pages: 5

Brand: Macally Pages: 10

Brand: PAC Pages: 4

928 GT - 1991 WIRE DIAGRAM

Brand: Porsche Pages: 30

Brand: Telwin Pages: 32

Brand: Nav TV Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands