Home
/
Mazda
/
2006 Tribute
/
Owner'S Manual

Mazda 2006 Tribute, Owner'S Manual, Page: 241 / 282

Share

Page: 241 / 282

Mazda 2006 Tribute Owner'S Manual Download Page 241

JOBNAME: No Job Name PAGE: 241 SESS: 1 OUTPUT: Wed Jun 15 16:24:35 2005
/ford_pdm/ford/own2002/j14/mpdiff

detergent. Rinse thoroughly with clean water. To avoid damaging the
blades, do not use fuel, kerosene, paint thinner or other solvents.

Changing the wiper blades

1. Pull the wiper arm away from

the vehicle. Turn the blade at an
angle from the wiper arm. Push
the lock pin manually to release
the blade and pull the wiper
blade down toward the
windshield to remove it from
the arm.

2. Attach the new wiper to the

wiper arm and press it into
place until a click is heard.

Replace wiper blades at least once
per year for optimum performance.

Poor wiper quality can be improved
by cleaning the wiper blades and
the windshield, refer to

Windows and wiper blades

in the

Cleaning

chapter.

To prolong the life of the wiper blades, it is highly recommended to
scrape off the ice on the windshield before turning on the wipers. The
layer of ice has many sharp edges and can damage the micro edge of the
wiper rubber element.

ENGINE OIL

Checking the engine oil

Refer to

service maintenance section

for the appropriate intervals for

checking the engine oil.

1. Make sure the vehicle is on level ground.

2. Turn the engine off and wait a few minutes for the oil to drain into

the oil pan.

3. Set the parking brake and ensure the gearshift is securely latched in

P (Park) (automatic transmissions) or 1 (First) (manual
transmissions).

4. Open the hood. Protect yourself from engine heat.

5. Locate and carefully remove the engine oil level indicator (dipstick).

CIMS #1014724

com_chnge_blades.2003

itdseq=290

CIMS #52549

com_oil

itdseq=291

CIMS #514009

com_check-oil.204

itdseq=292

art=ctomc707_a

DIFF-MARKED Review Copy ——
(OLD=2006 Tribute fus Owners Guide (post-2002-fmt) 06.5 Tribute Champ (#26074) (May-02-2005 14:29:19))
(NEW=2006 Tribute fus Owners Guide (post-2002-fmt) 2006.5 Tribute CNE Review (#26074) (Jun-15-2005
16:18:13))
2006 Tribute (j14), Owners Guide (post-2002-fmt) (own2002), Market: USA (fus)

PAGE: 241 OP: root EDIT SESSION: 1 DATE: JUNE 15 2005 at 16:24 JOB: @ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_j14/DIV_mpdiff

Maintenance and Specifications

241

«
...
239
240
241
242
243
...
»

Summary of Contents for 2006 Tribute



























































































































































































































































































Reviews:

No comments