Home
/
Mazda
/
2006 Tribute
/
Owner'S Manual

Mazda 2006 Tribute, Owner'S Manual, Page: 171 / 282

Share

Page: 171 / 282

Mazda 2006 Tribute Owner'S Manual Download Page 171

JOBNAME: No Job Name PAGE: 171 SESS: 1 OUTPUT: Wed Jun 15 16:24:35 2005
/ford_pdm/ford/own2002/j14/mpdiff

•

Start the engine

•

Depress the brake pedal

•

Move the gearshift lever into the desired gear

To put your vehicle in P (Park):

•

Come to a complete stop

•

Move the gearshift lever and securely latch it in P (Park)

WARNING: Always set the parking brake fully and make sure
the gearshift is latched in P (Park). Turn the ignition to the
LOCK position and remove the key whenever you leave your
vehicle.

R (Reverse)

With the gearshift lever in R (Reverse), the vehicle will move backward.
Always come to a complete stop before shifting into and out of R
(Reverse).

N (Neutral)

With the gearshift lever in N (Neutral), the vehicle can be started and is
free to roll. Hold the brake pedal down while in this position.

D (Overdrive)

The normal driving position for the
best fuel economy. Transaxle
operates in gears one through four.
D (Overdrive) can be deactivated by
pressing the O/D OFF switch on the
side of the gearshift lever. This will
illuminate the O/D OFF light and
deactivate the overdrive.

Drive (O/D OFF switch pressed)

Drive is activated when the O/D OFF switch is pressed.

•

This position allows for all forward gears except overdrive.

•

O/D OFF light is illuminated.

•

Provides engine braking.

•

Use when driving conditions cause excessive shifting from O/D to
other gears. Examples: city traffic, hilly terrain, heavy loads, trailer
towing and when engine braking is required.

art=204gf011_a

DIFF-MARKED Review Copy ——
(OLD=2006 Tribute fus Owners Guide (post-2002-fmt) 06.5 Tribute Champ (#26074) (May-02-2005 14:29:19))
(NEW=2006 Tribute fus Owners Guide (post-2002-fmt) 2006.5 Tribute CNE Review (#26074) (Jun-15-2005
16:18:13))
2006 Tribute (j14), Owners Guide (post-2002-fmt) (own2002), Market: USA (fus)

PAGE: 171 OP: root EDIT SESSION: 1 DATE: JUNE 15 2005 at 16:24 JOB: @ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_j14/DIV_mpdiff

Driving

171

«
...
169
170
171
172
173
...
»

Summary of Contents for 2006 Tribute



























































































































































































































































































Reviews:

No comments