Home
/
Mazda
/
2006 Tribute
/
Owner'S Manual

Mazda 2006 Tribute, Owner'S Manual, Page: 154 / 282

Share

Page: 154 / 282

Mazda 2006 Tribute Owner'S Manual Download Page 154

JOBNAME: No Job Name PAGE: 154 SESS: 1 OUTPUT: Wed Jun 15 16:24:35 2005
/ford_pdm/ford/own2002/j14/mpdiff

Special loading instructions for owners of pickup trucks and
utility-type vehicles

WARNING: For important information regarding safe operation
of this type of vehicle, see the Preparing to drive your vehicle
section in the Driving chapter of this Owner’s Guide.

WARNING: Loaded vehicles may handle differently than
unloaded vehicles. Extra precautions, such as slower speeds and
increased stopping distance, should be taken when driving a
heavily loaded vehicle.

Your vehicle can haul more cargo and people than most passenger cars.
Depending upon the type and placement of the load, hauling cargo and
people may raise the center of gravity of the vehicle.

TRAILER TOWING

Trailer towing with your vehicle may require the use of a trailer tow
option package.

Trailer towing puts additional loads on your vehicle’s engine, transaxle,
axle, brakes, tires, and suspension. For your safety and to maximize
vehicle performance, be sure to use the proper equipment while towing.

Follow these guidelines to ensure safe towing procedure:

•

Be sure to locate all the warnings supplied by the trailer rental or
sales company and study the unique requirements of each trailer you
intend to tow.

•

Stay within your vehicle’s load limits.

•

Thoroughly prepare your vehicle for towing. Refer to

Preparing to

tow

in this chapter.

•

Use extra caution when driving while trailer towing. Refer to

Driving

while you tow

in this chapter.

•

Service your vehicle more frequently if you tow a trailer. Refer to the
“Scheduled Maintenance” section of this manual.

•

Do not tow a trailer until your vehicle has been driven at least 500
miles (800 km).

•

Refer to the instructions included with towing accessories for the
proper installation and adjustment specifications.

Do not exceed the maximum loads listed on the Safety Compliance
Certification Label. For load specification terms found on the label, refer

CIMS #954537

com_loading-warnings.fly

itdseq=184

CIMS #101936

com_towing.title

itdseq=185

CIMS #602421

com_towing.j14

itdseq=186

DIFF-MARKED Review Copy ——
(OLD=2006 Tribute fus Owners Guide (post-2002-fmt) 06.5 Tribute Champ (#26074) (May-02-2005 14:29:19))
(NEW=2006 Tribute fus Owners Guide (post-2002-fmt) 2006.5 Tribute CNE Review (#26074) (Jun-15-2005
16:18:13))
2006 Tribute (j14), Owners Guide (post-2002-fmt) (own2002), Market: USA (fus)

PAGE: 154 OP: root EDIT SESSION: 1 DATE: JUNE 15 2005 at 16:24 JOB: @ibm2/ford_pdm/CLS_ford/GRP_own2002/JOB_j14/DIV_mpdiff

Tires, Wheels and Loading

154

«
...
152
153
154
155
156
...
»

Summary of Contents for 2006 Tribute



























































































































































































































































































Reviews:

No comments