Home
/
MA lighting
/
MA VPU
/
User Manual

MA lighting MA VPU, User Manual, Page: 105 / 218

Share

Page: 105 / 218

MA lighting MA VPU User Manual Download Page 105

© 2018 MA Lighting Technology GmbH - Dachdeckerstr. 16 - 97297 Waldbüttelbrunn - Germany
Phone +49 5251 688865-30 - [email protected] - www.malighting.com

1

9.4. Toolbar

The toolbar contains several buttons that are related to the general operations of the program.

Toolbar

Network…

Shows the actual network state or opens the MA Network dialog as described in:

File...

Toggle GUI <-> Fullscreen:

Switches the GUI (Graphical User Interface) off. You can also use the 'Shift + Enter’ key on the keyboard to switch

the GUI off.

Leave or switch to fullscreen mode with the 'Shift + Enter’ button.

Hint

:

MA VPU always runs in fullscreen view.

Only if the VPU is installed on a PC with a protection dongle (former grandMA Video application) the

switching between windowed and fullscreen is relevant.

Therefore you can use the „Alt + Enter" key.

Show Mode:

This mode avoids interruptions of the running show caused by manual operations of a user.

Also non essential functionality is reduced or disabled to increase the performance.

It can be set by a channel in the Master fixture or this button.

The following actions are performed:

GUI is disabled

Thumbnails are not distributed to avoid network traffic

Preview of the outputs of the VPU is set to Pause

Frame rate of the GUI screen (if turned on) is limited to 10 fps

Frame rate of the VPU Plus internal screen is limited to 5 fps

No clip preview is displayed at Content Editor

Speed of content distribution is reduced to 10 %

Highlight functionality of the pixel mapper is turned off

CITP is disabled

Testpattern is disabled

Monitor identification is disabled

Hap Converter is paused

105 of 218

grandMA2 User Manual - Program surface
Version 3.4 – 2018-07-25
English

«
...
103
104
105
106
107
...
»

Summary of Contents for MA VPU



























































































































































































































Reviews:

No comments