![background image](http://html1.mh-extra.com/html/lutron-electronics/grafik-eye-qs/grafik-eye-qs_installation-and-operation-manual_1950621045.webp)
®
GRAFIK Eye
®
QS Control Unit Installation and Operation Guide 45
For Sivoia
®
QS
Window Treatments
wired directly to the GRAFIK Eye
®
QS
control unit:
To associate or disassociate
window
treatments with a shade button group:
1. On the GRAFIK Eye
®
QS control unit
shade button group you wish to assign
window treatments to, enter window
treatment programming mode: Press and
hold the top (open) and bottom (close)
buttons simultaneously for 3 seconds.
The top and bottom LEDs will flash.
Window treatments that are unassigned
will move to up (open), and window
treatments that are assigned will move to
close (down).
2. Tap the top (open) button to start
assigning.
3. Tap the top (open) button repeatedly to
cycle forward through the addresses;
tap the bottom (close) button to cycle
backward.
4. Press the shade group
lower
button to
associate the window treatment.
Press the shade group
raise
button to
disassociate
the window treatment.
5. Exit window treatment programming
mode: Press and hold the top (open) and
bottom (close) buttons simultaneously for
3 seconds. The top and bottom LEDs will
stop flashing.
When a GRAFIK Eye
®
QS system consists of Sivoia
®
QS window treatments (shades) and a GRAFIK Eye
®
QS with one or more shade button groups, you can associate the shade button groups on the control unit
with the window treatments so the shade buttons can directly control the window treatments.
Associating Sivoia
®
QS Window Treatments and GRAFIK Eye
®
QS Control Units
Press and hold the top
(open) and bottom (close)
buttons on the GRAFIK
Eye
®
QS control unit shade
button group to enter or
exit window treatment
programming mode.
OK
Open
Preset
Close
Sivoia
®
QS Wireless
window treatment
EDU
LED
For Wireless Sivoia
®
QS
Window Treatments:
To associate window treatments with a shade button
group:
1. Make sure the wireless mode of the GRAFIK Eye
®
QS control
unit is “Enabled”.
2. On the GRAFIK Eye
®
QS control unit shade button group you
wish to assign window treatments to, enter window treatment
programming mode: Press and hold the top (open) and
bottom (close) buttons simultaneously for 3 seconds. The top
and bottom LEDs will flash.
3. The LEDs on the electronic drive unit (EDU) and the wireless
antenna of unassociated window treatments will blink slowly.
On the window treatment that you wish to associate with the
shade button group, tap any button; the LED on the EDU
will blink rapidly to indicate the window treatment is now
associated with the shade button group on the GRAFIK Eye
®
QS control unit.
4. Repeat step 2 to associate additional window treatments to
that shade button group.
5. Exit window treatment programming mode: Press and hold
the top (open) and bottom (close) buttons simultaneously for
3 seconds. The top and bottom LEDs will stop flashing.
6. Repeat steps 1 through 5 for additional shade button groups,
as applicable.
To disassociate
window treatments with a shade button
group:
Repeat, in the same order, the steps above for associating
window treatments. When in window treatment programming
mode, tap any button on the electronic drive unit (EDU) of
the window treatments that you wish to disassociate from
the shade button group; the green LEDs on the EDU and
antenna will blink slowly to indicate the window treatment is
disassociated from the shade button group on the GRAFIK
Eye
®
QS control unit.
Note:
The wireless signal has a range of 9 m through
standard construction or 18 m line of sight.
Lower button: Press to
associate
Raise button: Press to
disassociate