LS ELECTRIC H100 Series, Manual

Page: 42 / 84

42
_ LS ELECTRIC
Fan and Pump
H100
Application Function Group
Application 1 Function Group
Code Comm. No. Name LCD Display Set Range Default Attribute *
80 0h1A50 Reference compensation of first aux. motor Aux1 Ref Comp 0.00~Unit Band 0.00 O
81 0h1A51
Reference compensation of second aux. motor
Aux2 Ref Comp 0.00~Unit Band 0.00 O
82 0h1A52
Reference compensation of third aux. motor
Aux3 Ref Comp 0.00~Unit Band 0.00 O
83 0h1A53
Reference compensation of fourth aux. moto
r
Aux4 Ref Comp 0.00~Unit Band 0.00 O
84
0h1A54 Reference compensation of fifth aux. motor Aux5 Ref Comp 0.00~Unit Band 0.00 O
90 0h1A5A Interlock selection Interlock
0 No
0: No O
1 Yes
91
0h1A5B
Delay time before running the next main motor when
interlock/auto change occurs at the main motor
Interlock DT 0.1~360.0(Sec) 5.0 O
95 1
Oh1A5F
Selection of Auxiliary motor to display
[AP1-96] [AP1-97]
AuxRunTime Sel
0: Aux 1
0: Aux 1 O
1: Aux 2
2: Aux 3
3: Aux 4
4: Aux 5
96 Oh1A60
Operation time(Day) of Auxiliary motor
selected in [AP1-95]
AuxRunTime Day 0 ~ 65535 O O
97
Oh1A61
Operation time of Auxiliary motor selected
in [AP1-95] (Hour:Minute)
AuxRunTime Min 00:00 ~ 23:59 00:00 O
98 Oh1A62
Deleting operation time of Auxiliary
motor
AuxRunTime Clr
0 None
0: None O
1 All
2 Aux 1
3 Aux 2
4 Aux 3
5 Aux 4
6 Aux 5
1
AP1-95~98 is available when MMC and Master Follower functions are performed.
Application 2 Function Group
Code Comm. No. Name LCD Display Set Range Default Attribute *
00 - Jump code Jump Code 1~99 40 O
01 1 0h1B01 Load curve tuning Load Tune
0 No
No Δ
1 Yes
02 0h1B02 Load curve: Low Freq Load Fit Lfreq Base Freq*15%~Load Fit HFreq 30.00 Δ
03
0h1B03 Current at Low Freq Load Fit LCurr 0.0~80.0(%) 40.0 Δ
04 0h1B04 Power at Low Freq Load Fit LPwr 0.0~80.0(%) 30.0 Δ
08 0h1B08 Load curve: High Freq Load Fit Hfreq Load Fit LFreq~High Freq 51.00 Δ
09 0h1B09 Current at High Freq Load Fit HCurr Load Fit HCurr~200.0(%) 80.0 Δ
10 0h1B0A Power at High Freq Load Fit HPwr Load Fit HPwr~200.0(%) 80.0 Δ
11
0h1B0B Load curve current Load Curve Cur - - X
12 0h1B0C Load curve power Load Curve Pwr - - X
15 0h1B0F Pump Clean Setting 1 Pump Clean Mode1
0 None
0: None O
1 DI Defendant
2 Output Power
3 Output Current
16 0h1B10 Pump Clean Setting 2 Pump Clean Mode2
0 None
0: None Δ
1 Start
2 Stop
3 Start&Stop
17
0h1B11 Pump clean load setting PC Curve Rate 0.1~200.0(%) 100.0 O
18 0h1B12 Pump clean reference band PC Curve Band 0.0~100.0(%) 5.0 O
19 0h1B13 Pump clean operation delay time PC Curve DT 0.0~6000.0(sec) 60.0 O
20 0h1B14 Pump clean available area holding time PC Start DT 0.0~6000.0(sec) 10.0 O
21 0h1B15
0operationtimewhenforward/reverseswitching
PC Step DT 0.1~6000.0(sec) 5.0 O
22
0h1B16 Pump clean acceleration time PC Acc Time 0.0~600.0(sec) 10.0 O
23 0h1B17 Pump clean deceleration time PC Dec Time 0.0~600.0(sec) 10.0 O
24 0h1B18 Forward step steady time Fwd SteadyTime 0.0~600.0(sec) 10.0 O
25 0h1B19 Forward step steady frequency Fwd SteadyFreq 0.00, Low Freq~High Freq 30.00 O
26 0h1B1A Reverse step steady time Rev SteadyTime 0.0~600.0(sec) 10.0 O
27
0h1B1B Reverse step steady frequency Rev SteadyFreq 0.00, Low Freq~High Freq 30.00 O
28 0h1B1C
Number of forward/
reverse steps during pump cleaning
PC Num of Steps 1~10 2 O
29 0h1B1D Pump clean cycle monitoring Repeat Num Mon - - X
30 0h1B1E Number of repeated pump cleaning Repeat Num Set 0~10 2 O
1
Set the operation mode to AUTO to configure AP2-01