LS ELECTRIC H100 Series, Manual

Page: 47 / 84

H100 _
47
Energy Saving Drive
Code Comm. No. Name LCD Display Set Range Default Att ribute *
37 0h1D25 Overheat motor sensor failure area Thermal-T
0 Low
0: Low O
1 High
38 1 0h1D26 Overheat motor detection sensor ThermalMonitor - - X
40 0h1D28 Overheat motor trip selection ETH Trip Sel
0 None
0: None 1 Free-Run
O
2 Dec
41 0h1D29 Motor cooling fan type Motor Cooling
0 Self-cool
0: Selfcool O
1 Forced-cool
42
0h1D2A Overheat prevention: 1 min. rating ETH 1min ETH Cont~150(%) 120 O
43 0h1D2B Overheat prevention: continuous rating ETH Cont 50~120(%) 100 O
44 0h1D2C Fire Mode setting password Fire Mode PW 0~9999 0 O
45 2 0h1D2D Fire Mode setting Fire Mode Sel
0 None
0: None O 1 Fire Mode
2 Test Mode
46 3 0h1D2E Fire Mode direction setting Fire Mode Dir
0 Reverse
1: Forward O
1 Forward
47 4 0h1D2F Fire Mode speed setting Fire Mode Freq 0~max Freq 60.00 O
48 0h1D30 Fire Mode operation count Fire Mode Cnt - 0 X
50 0h1D32 Stall prevention & flux breaking Stall Prevent
Bit 0000~1111
0100 Δ
Bit 0 Accelerating
Bit 1 In constant speed
Bit 2 Decelerating
Bit 3 Flux Braking
51 0h1D33 Stall frequency 1 Stall Freq 1 Start frequency ~Stall frequency 2(Hz) 60.00 O
52 0h1D34 Stall level 1 Stall Level 1 30~150(%) 130 Δ
53 0h1D35 Stall frequency 2 Stall Freq 2 Start frequency 1 ~Stall frequency 3(Hz) 60.00 O
54 0h1D36 Stall level 2 Stall Level 2 30~150(%) 130 Δ
55 0h1D37 Stall frequency 3 Stall Freq 3 Start frequency2 ~Stall frequency 4(Hz) 60.00 O
56 0h1D38 Stall level 3 Stall Level 3 30~150(%) 130 Δ
57
0h1D39 Stall frequency 4 Stall Freq 4 Stall frequency 3~Max. frequency (Hz) 60.00 O
58 0h1D3A Stall level 4 Stall Level 4 30~150(%) 130 Δ
59
0h1D3B Flux Braking voltage gain Flux Brake Kp
5.5~90kW 0~150(%)
0 O
110~500kW 0~10(%)
60 0h1D3C Pipe broken detection setting PipeBroken Sel
0 None
0: None O
1 Warning
2 Free-Run
3 Dec
61 0h1D3D Pipe broken detection level PipeBroken Lev 0~100.0(%) 97.5 O
62 0h1D3E Pipe broken detection time setting PipeBroken DT 0.0~6000.0(Sec) 10.0 O
66 0h1D42 Damping resistance use rate DB Warn %ED 0~30(%) 0 O
70 0h1D46 Level detection mode selection LDT Sel
0 None
0 : None O
1 Warning
2 Free-Run
3 Dec
71 0h1D47 Setting level detection mode LDT Area Sel
0 Below Level
0: Below Level O
1 Above Level
72 0h1D48 Level detection source LDT Source
0 Output Current
0: Output Current O
1 DC Link Voltage
2 Output Voltage
3 kW
4 HP
5 V1
6 V2
7 I2
8 PID Ref Value
9 PID Fdb Value
10 PID Output
11 EPID1 Fdb Val
12 EPID2 Fdb Val
1
PRT-38 code appears when PRT-34 code is not 0: None.
2
PRT-45 can only be set when PRT-44 is in Fire mode. To change the mode in PRT-44, create a new password for PRT-44.
3
PRT-46–47 are displayed when PRT-45 is not set to ‘0 (NONE)’
.
4
When Fire mode is set at PRT-45, PRT-46 is automatically set to forward, and the frequency set at PRT-47 cannot be edited. When PRT-45 is set to Test mode, PRT-46 and PRT-47 settings are editable.