background image

5. Transport, delivery and 
storage

5.1 Transport

SKF products are packaged in accordance with the regulations of the 
recipient country and in accordance with DIN ISO 9001. Our products 
must be transported with care. Products must be protected against 
mechanical influences such as impacts. Transport packaging must be 
labeled with the information 'Do not drop!'.

There are no restrictions relating to land, air, or sea transportation.

5.2 Delivery

Following receipt of the shipment, the product or products must be 
checked for damage and the shipping documents should be used to 
make sure that the delivery is complete. Keep the packaging material 
until any and all problems have been clarified.

5.3 Storage

The following conditions apply to the storage of SKF products.

5.3.1 Storage of lubrication units

•  Ambient conditions: dry, dust-free environment; storage in 

well-ventilated, dry area

•  Storage time: 24 months max.
•  Permitted air humidity: < 65%
•  Warehouse temperature: 10 to 40 °C
•  Light: direct sunlight/UV radiation must be avoided; nearby 

sources of heat must be screened

5.3.2 Storage of electronic and electrical 
devices

•  Ambient conditions: dry, dust-free environment; storage in 

well-ventilated, dry area

•  Storage time: 24 months max.
•  Permitted air humidity: < 65%
•  Warehouse temperature: 10 – 40 °C
•  Light: direct sunlight/UV radiation must be avoided; nearby 

sources of heat must be screened

5.3.3 Storage – general information

•  Ensure that no dust gets into stored products by wrapping them in 

plastic film

•  Store products on racks or pallets to protect them from damp 

floors

•  Before placing products into storage, protect uncoated metal sur-

faces - and drive parts and mount surfaces in particular - from 
corrosion using long-term corrosion protection.

CAUTION

The product must not be tipped up or dropped.

15

Summary of Contents for SKF CLK







































Reviews: