Lexmark Pro910 Series Service Manual Download Page 24

Page: 24 / 118

2-4

Service Manual

Lexmark Pro910 Series

Go Back

Printhead stall

Printhead Cannot Move

Remove any obstructions to
the Printhead inside the
Printer. Close the Cover,
and then touch OK.

Technical Support Center:

Turn off the printer. Open the printer
cover, and clear the carrier path from
any obstruction. If the problem
remains, then replace the printer.

Service:

Go to

“Carrier service checks” on

page 2-14

Printhead short and other errors

Printhead Error

Printhead Error [x]

Technical Support Center:

Clean the printhead contacts and
nozzles. See

“Cleaning the

printhead nozzles and contacts” on
page 6-2

. If the problem remains,

then replace the printhead.

Service:

Clean the printhead contacts and
nozzles. See

“Cleaning the

printhead nozzles and contacts” on
page 6-2

. If the problem remains,

then replace the printhead.

Printhead warning messages

Printhead recovery warning

Printhead Warning

Clean Printhead or Deep
Clean Printhead may be
required. To clean the
Printhead, navigate to Ink
More Options menu.

Technical Support Center:

1. Touch

to clear the warning.

2. Clean the printhead nozzles. See

“Cleaning the printhead” on
page 6-2

Service:

1. Touch

to clear the warning.

2. Clean the printhead nozzles. See

“Cleaning the printhead” on
page 6-2

Printhead error messages

Error

Control panel message

Action

Summary of Contents for Pro910 Series























































































































Search results

Summary of Contents for Pro910 Series

Reviews:

Related manuals for Pro910 Series

Brands by name

Popular brands

Lexmark Pro910 Series, Service Manual

Search results

Summary of Contents for Pro910 Series

Reviews:

Related manuals for Pro910 Series

Brands by name

Popular brands