Lexmark Pro910 Series Service Manual Download Page 105

Page: 105 / 118

Preventive maintenance

6-1

Lexmark Pro910 Series

Go Back

6. Preventive maintenance

This chapter describes procedures for printer preventive maintenance. Follow these recommendations to help
prevent problems and maintain optimum performance.

Lubrication specifications

Lubricate only when parts are replaced or as needed, not on a scheduled basis. Use grease to lubricate the
following:

•

All gear mounting studs

•

The left and right ends of the large feed roller at the side frames

•

The carrier to carrier frame engagement

•

The carrier guide rod, and carrier guide rod bearings

Warning:

Grease may cause printer damage or failure when it comes into contact with some components.

Keep grease away from the following:

•

Electrical components

•

Rollers along the paper path

•

Printhead

•

Encoder strip

•

Paper pick rollers

Summary of Contents for Pro910 Series























































































































Search results

Summary of Contents for Pro910 Series

Reviews:

Related manuals for Pro910 Series

Brands by name

Popular brands

Lexmark Pro910 Series, Service Manual

Search results

Summary of Contents for Pro910 Series

Reviews:

Related manuals for Pro910 Series

Brands by name

Popular brands