Lexmark Pro910 Series Service Manual Download Page 31 | Manualshive

Page: 31 / 118

background image

Diagnostic information

2-11

Lexmark Pro910 Series

Go Back

Previous

Next

Serial flash error

Invalid parameters have been passed
to ReadFlashPage.

Technical Support Center:

Unplug the printer from the electrical
outlet, wait for 10 seconds, and then
plug the printer back in. If the problem
remains, then replace the printer.

Service:

Replace the system board. See

“System board removal” on
page 4-35

Undefined signal error

Microprocessor has encountered a
bad signal (other than an abort, illegal
instruction, or arithmetic exception).

Technical Support Center:

Unplug the printer from the electrical
outlet, wait for 10 seconds, and then
plug the printer back in. If the problem
remains, then replace the USB cable.

Service:

Replace the system board. See

“System board removal” on
page 4-35

Unlock scanner

Scanner mechanism is locked in place
or unable to move due to other failure.

Technical Support Center:

Unplug the printer from the electrical
outlet, wait for 10 seconds, and then
plug the printer back in. If the problem
remains, then replace the printer.

Service:

Replace the scanner unit. See

“Scanner unit removal” on
page 4-30

Scan carrier stall

The scan carrier has stalled.

Technical Support Center:

Unplug the printer from the electrical
outlet, wait for 10 seconds, and then
plug the printer back in. If the problem
remains, then replace the printer.

Service:

Replace the scanner unit. See

“Scanner unit removal” on
page 4-30

Undefined error

The microprocessor has encountered
an abort or undefined instruction.

Technical Support Center:

Unplug the printer from the electrical
outlet, wait for 10 seconds, and then
plug the printer back in. If the problem
remains, then replace the printer.

Service:

Replace the system board. See

“System board removal” on
page 4-35

Error table

Error

Description

Action

«
...
29
30
31
32
33
...
»

Summary of Contents for Pro910 Series























































































































Reviews:

No comments

Related manuals for Pro910 Series

Brand: TDT Pages: 15

ExpressCard 2000

Brand: Magtek Pages: 25

Brand: Xerox Pages: 418

Donation Point Even

Brand: Quest Payment Systems Pages: 2

WorkCentre WC7530

Brand: Xerox Pages: 280

Brand: Brother Industries Pages: 501

Brand: DataMetrics Pages: 46

Brand: Output Technology Pages: 67

Brand: Cashino Pages: 54

1275n - Optra SC Color Laser Printer

Brand: Lexmark Pages: 6

Workcentre 3635

Brand: Xerox Pages: 22

WORKCENTRE 5150

Brand: Xerox Pages: 4

Brand: IBM Pages: 64

2121L - FaxCentre B/W Laser

Brand: Xerox Pages: 226

Brand: Xerox Pages: 4

OptiPrinter PRO

Brand: Verity Systems Pages: 37

Brand: Star Micronics Pages: 276

Brand: LabelMill Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands