Lexmark Interpret S400 User Manual Download

Page: 120 / 179

Print job does not print or is missing pages

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

AKE

SURE

THE

INK

CARTRIDGES

ARE

INSERTED

CORRECTLY

Turn the printer on, and then open the printer.

Make sure the cartridges are inserted correctly.

The cartridges should

click

firmly into the matching color slot of the printhead.

Close the printer.

ELECT

YOUR

PRINTER

FROM

THE

RINT

DIALOG

BEFORE

SENDING

THE

PRINT

JOB

Note:

This solution applies to Macintosh users only.

With a document open, choose

File

Print

From the printer pop-up menu, choose your printer, and then click

Print

If your printer does not appear on the Printer list, then choose

Add Printer

. From the list of printers in the Default

tab, select your printer, and then click

Add

If your printer does not appear on the list, then try either of the following:

•

For a USB-connected printer, remove and then reconnect the USB cable.

•

For a printer that is wirelessly connected, see the Wireless troubleshooting section.

AKE

SURE

THE

PRINT

JOB

NOT

PAUSED

AKE

SURE

YOUR

PRINTER

SET

THE

DEFAULT

PRINTER

ECONNECT

THE

PRINTER

POWER

SUPPLY

Turn off the printer.

Note:

Make sure the printer is not in Power Saver mode. Press and hold for three seconds to turn off the printer.

Unplug the power cord from the wall outlet, and then pull out the power cord from the power supply.

After one minute, reconnect the power cord into the power supply, and then plug the power cord into the wall
outlet.

Turn on the printer.

EMOVE

AND

RECONNECT

THE

USB

CABLE

CONNECTED

YOUR

PRINTER

HECK

THE

USB

CONNECTION

Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

Firmly plug the square end of the USB cable into the back of the printer.

Troubleshooting

120

Summary of Contents for Interpret S400




















































































































































































Search results

Summary of Contents for Interpret S400

Reviews:

Related manuals for Interpret S400

Brands by name

Popular brands

Lexmark Interpret S400, User Manual

Search results

Summary of Contents for Interpret S400

Reviews:

Related manuals for Interpret S400

Brands by name

Popular brands