manualshive.com logo in svg

Lexmark C792de, Service Manual

The Lexmark C792de is a high-quality color laser printer perfect for any office setting. For troubleshooting and maintenance, download the free Service Manual from our website. This comprehensive manual will guide you through any technical issues, ensuring your printer stays running smoothly. Download it now from manualshive.com.

Share
Download
background image

Table of contents

v

5062

241.03, 242.03, 243.03, 244.03, 242.05, 243.05, 244.05, 245.05—Paper jam (550-sheet/2000-sheet input 
option) service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-96
242.08, 243.08, 244.08, 245.08—Paper jam (550-sheet/2000-sheet input option) service check   . .  2-98
250.21, 250.22—MPF motor error service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-100
900.xx—Software error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-102
938.16—MPF paper out sensor error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-103
938.18—Waste toner sensor error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-104
938.19—Waste toner full sensor error service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-105
938.27, 938.29, 938.30—Weather station error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-106
938.28—Remote weather station error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-107
950.00–950.29—EPROM mismatch failure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-108
956.xx—System board failure service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-109
990.01—POST error (2000-sheet input option) service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-109
990.05—POST error (550-sheet input option) service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-111
Bubble sensor service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-112
D1 and D2 sensor service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-114
Dead printer service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-117
Double feed (550-sheet/2000-sheet input option) service check . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-118
Input option not detected (550-sheet/2000-sheet input option) service check   . . . . . . . . . . . . . . . .  2-120
Input, S1, narrow media, and near narrow media sensor service check  . . . . . . . . . . . . . . . . . . . . .  2-121
Jam clearance cover open (550-sheet/2000-sheet input option) service check   . . . . . . . . . . . . . . .  2-123
Media size error (550-sheet/2000-sheet input option) service check.  . . . . . . . . . . . . . . . . . . . . . . .  2-125
Media tray missing (550-sheet input option) service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-126
Media tray missing (2000-sheet input option) service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-127
Networking service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-129
Bin-full sensor service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-131
Pick arm stuck down service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-132
Redrive bubble sensor service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-133
Skew (550-sheet input option) service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-134
Skew (2000-sheet input option) service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-135
Tray empty (2000-sheet input option) service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-137
Tray jam indicator (550-sheet/2000-sheet input option) service check  . . . . . . . . . . . . . . . . . . . . . .  2-139
Tray linking service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-139

Diagnostic aids

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

3-1

Understanding the operator panel and menus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1

Operator panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1
Understanding the home screen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-2
Using the touch-screen buttons  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-2
Other touch-screen icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-4
Administrative menus   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-5

Accessing service menus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-6
Diagnostics menu   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-7

Diagnostics menus   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-7
Exiting the Diagnostics mode   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-9
DUAL DIODE ADJUST  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-9
REGISTRATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-9
Alignment Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-10

Setting alignment for color   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-10
Adjusting Linearity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-11
Drift Sensors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-12

MISC TESTS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-12

Toggle ITU  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-12
Printhead Inst   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-12
Auto Detect  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-13

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

IBM 3130 Planning Manual preview
3130
Brand: IBM Pages: 112
Canon MultiPASS L6000 User Manual preview
MultiPASS L6000
Brand: Canon Pages: 251
Canon MultiPASS C5500 Quick Start Manual preview
MultiPASS C5500
Brand: Canon Pages: 24
Canon MultiPASS L6000 Quick Start Manual preview
MultiPASS L6000
Brand: Canon Pages: 24
Canon Laser Class 700 Series Reference Manual preview
Laser Class 700 Series
Brand: Canon Pages: 221
Oki B2200 Specifications preview
B2200
Brand: Oki Pages: 2
Magtek ExpressCard 2000 Preventive Maintenance Procedure preview
ExpressCard 2000
Brand: Magtek Pages: 25
QMS Magicolor 2 Desklaser Install Manual preview
Magicolor 2 Desklaser
Brand: QMS Pages: 60
Xante Ilumina Repacking And Shipping Manual preview
Ilumina
Brand: Xante Pages: 6
Xerox WorkCentre Pro 421 Brochure & Specs preview
WorkCentre Pro 421
Brand: Xerox Pages: 4
Xerox WorkCentre Pro 412 User Manual preview
WorkCentre Pro 412
Brand: Xerox Pages: 212
Xerox WORKCENTRE PE 220 Evaluator Manual preview
WORKCENTRE PE 220
Brand: Xerox Pages: 8
Xerox WORKCENTRE PE 220 Setup Manual preview
WORKCENTRE PE 220
Brand: Xerox Pages: 2
Xerox WORKCENTRE PE 220 User Manual preview
WORKCENTRE PE 220
Brand: Xerox Pages: 200
Xerox WorkCentre m940 User Manual preview
WorkCentre m940
Brand: Xerox Pages: 86
Xerox WorkCentre M15 Quick Start Manual preview
WorkCentre M15
Brand: Xerox Pages: 24
Xerox WorkCentre PE16 User Manual preview
WorkCentre PE16
Brand: Xerox Pages: 201
Xerox WorkCentre M24 Color User Manual preview
WorkCentre M24 Color
Brand: Xerox Pages: 441

Brands by name

Popular brands

Load more brands