Lexmark C792de Service Manual Download Page 155 | Manualshive

Page: 155 / 630

background image

Diagnostic information

2-117

5062

Dead printer service check

A dead printer is a condition where the display is blank, the LED on the operator panel is off, no fans turn, no
motors turn, and the fuser lamp does not come on.

If a 550-sheet option assembly is installed, remove the option and check the base printer for correct operation. If
the base printer operates correctly, replace the 550-sheet option assembly.

Warning:

Observe all necessary ESD precautions when removing and handling the system board or any
installed option cards or assemblies. See

“Handling ESD-sensitive parts” on page 4-1

.

Remove any input and output paper handling options from the printer.

Step

Questions / actions

Yes

No

1

Is the AC line cord damaged?

Replace the line cord.

Go to step 2.

2

Turn the printer off, open the system board
shield, and remove the connector shield.

Check the system board for +5 V dc between
JLVPS1 pin 6 and ground.

Is the voltage correct?

Replace the system board.
See

“System board

removal” on page 4-142

.

Go to step 3.

3

Is the JLVPS1 cable correctly installed at
JLVPS1 on the system board?

Go to step 4.

Reseat the cable.

4

1. Turn the printer off.
2. Disconnect the JLVPS1 cable from the

system board.

3. Turn the printer on, and then measure the

voltage between the JLVPS1 cable pin 6
and the pin 15 (black wire).

Does this measure approxi5 V dc?

Go to step 5.

Replace the LVPS. See

“Low-voltage power
supply (LVPS) removal”
on page 4-82

5

1. Turn the printer off.
2. Disconnect the cables in J5, JFSR1,

JHVPS, JCM1, JITM1, JKI1, JOOPT1,
and JYF1.

3. Connect the JLVPS1 cable to the system

board.

4. POR the printer.

Is the printer still dead?

Contact your next level of
support.

Go to step 6.

6

Connect one cable at a time, and POR the
printer.

Did you find the failing part?

Replace the failing part.

Contact you next level of
support.

CAUTION

When you see this symbol, there is a danger from hazardous voltage in the area of the product
where you are working. Unplug the product before you begin, or use caution if the product
must receive power in order to perform the task.

«
...
153
154
155
156
157
...
»

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

Brand: Wang Pages: 24

WORKCENTRE 5735

Brand: Xerox Pages: 50

Brand: Canon Pages: 394

Brand: Printronix Pages: 5

Brand: Oce Pages: 686

Brand: Tally Dascom Pages: 2

MINI THERMAL RP-3180

Brand: TVS electronics Pages: 19

4039 - B/W Laser Printer

Brand: Lexmark Pages: 49

Brand: Lexmark Pages: 64

Brand: Infotec Pages: 195

Brand: Savin Pages: 90

Brand: Ice Pages: 114

PocketJet 3 Plus

Brand: Brother Pages: 11

Brand: Brother Pages: 2

PT-2430PC - P-Touch 2430PC B/W Thermal Transfer Printer

Brand: Brother Pages: 2

Brand: Brother Pages: 4

Brand: Brother Pages: 165

PJ662 PocketJet 6 Print Engine with Bluetooth

Brand: Brother Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands