manualshive.com logo in svg

Lexmark C792de, Service Manual

The Lexmark C792de is a high-quality color laser printer perfect for any office setting. For troubleshooting and maintenance, download the free Service Manual from our website. This comprehensive manual will guide you through any technical issues, ensuring your printer stays running smoothly. Download it now from manualshive.com.

Share
Download
background image

Table of contents

ix

5062

Paper auto-size sensor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-113
Paper path redrive assembly with sensors removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-113
Paper pick mechanism assembly removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-116
Pick rolls removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-118
Printhead removal, installation, and alignment   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-119

Installing and coarse aligning the printhead  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-121
Aligning the printhead  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-124
Dual diode alignment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-124
Registration (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-125
Color alignment (cyan, yellow, and magenta)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-126

Redrive gears removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-129
Redrive motor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-130
Sensor (D1, D2, and fuser bubble) removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-132
Sensor (input, S1, narrow media, near narrow media) removal   . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-133
Speaker removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-134
Staging deflector assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-135
Staging paper path reference edge assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-136

Aligning the staging paper path reference edge  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-140

Standard media tray removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-142
System board removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-142
System board cage with board removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-145
Waste toner container removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-147
Waste toner gears removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-147
Waste toner sensor removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-148
Waste toner cable removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-149
Waste toner full cable removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-150
Waste toner full sensor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-151
Waste toner tray bracket removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-152

Input option removals   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-154
550-sheet tray  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-154

550-sheet drawer assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-155
550-sheet media tray assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-155
550-sheet tray controller card assembly removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-156
550-sheet tray deflector removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-158
550-sheet tray drive assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-159
550-sheet tray left anti-tip latch removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-162
550-sheet tray pass thru sensor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-164
550-sheet tray pick assembly removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-165
550-sheet tray pick roll assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-169
550-sheet tray right anti-tip latch assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-171
550-sheet tray top metal cover removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-172

2000-sheet high-capacity feeder  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-173

2000-sheet high-capacity feeder bellcrank assembly removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-173
2000-sheet high-capacity feeder controller card assembly removal  . . . . . . . . . . . . . . . . . . . . . . . .  4-174
2000-sheet high-capacity feeder drive assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-175
2000-sheet high-capacity feeder elevator home sensor removal   . . . . . . . . . . . . . . . . . . . . . . . . . .  4-179
2000-sheet high-capacity feeder jam clearance cover removal   . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-183
2000-sheet high-capacity feeder jam clearance top cover removal   . . . . . . . . . . . . . . . . . . . . . . . .  4-187
2000-sheet high-capacity feeder jam door clearance sensor removal   . . . . . . . . . . . . . . . . . . . . . .  4-188
2000-sheet high-capacity feeder LED bracket removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-190
2000-sheet high-capacity feeder left anti-tip latch assembly removal  . . . . . . . . . . . . . . . . . . . . . . .  4-191
2000-sheet high-capacity feeder left side cover removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-193
2000-sheet high-capacity feeder lift drive gear assembly removal   . . . . . . . . . . . . . . . . . . . . . . . . .  4-195
2000-sheet high-capacity feeder lift drive motor assembly removal   . . . . . . . . . . . . . . . . . . . . . . . .  4-201
2000-sheet high-capacity feeder media tray assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-204

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

Xerox All in One Printer Product Safety Data Sheet preview
All in One Printer
Brand: Xerox Pages: 3
Olympus P 400 Owner'S Manual preview
P 400
Brand: Olympus Pages: 71
Canon imageRUNNER ADVANCE C3330 Series Replacement Procedure preview
imageRUNNER ADVANCE C3330 Series
Brand: Canon Pages: 5
Canon imagePROGRAF TA-30 Setup Manual preview
imagePROGRAF TA-30
Brand: Canon Pages: 49
Canon LX-P1300 User Manual preview
LX-P1300
Brand: Canon Pages: 210
Canon Color imageCLASS MF8180c Starter Manual preview
Color imageCLASS MF8180c
Brand: Canon Pages: 34
FujiFilm Apeos 5580 Reference Manual preview
Apeos 5580
Brand: FujiFilm Pages: 37
JRC NKG-94 Instruction Manual preview
NKG-94
Brand: JRC Pages: 44
TEC B-370 Series Maintenance Manual preview
B-370 Series
Brand: TEC Pages: 89
idp SMART-81 User Manual preview
SMART-81
Brand: idp Pages: 104
Konica Minolta bizhub 160 Parts Manual Manual preview
bizhub 160
Brand: Konica Minolta Pages: 35
J&Maya JMB4 User Manual preview
JMB4
Brand: J&Maya Pages: 21
Oki C7500n Maintenance Manual preview
C7500n
Brand: Oki Pages: 192
Konica Minolta 4556-9598-01A User Manual preview
4556-9598-01A
Brand: Konica Minolta Pages: 84
Ricoh RN-MF1 Service Manual preview
RN-MF1
Brand: Ricoh Pages: 162
Evolis EDIKIO FLEX User Manual preview
EDIKIO FLEX
Brand: Evolis Pages: 45
Xerox WorkCentre Pro 421 System Administrator Manual preview
WorkCentre Pro 421
Brand: Xerox Pages: 162
Xerox WorkCentre 7970 System Administrator Manual preview
WorkCentre 7970
Brand: Xerox Pages: 268

Brands by name

Popular brands

Load more brands