manualshive.com logo in svg

Lexmark C792de, Service Manual

The Lexmark C792de is a high-quality color laser printer perfect for any office setting. For troubleshooting and maintenance, download the free Service Manual from our website. This comprehensive manual will guide you through any technical issues, ensuring your printer stays running smoothly. Download it now from manualshive.com.

Share
Download
background image

iv

Service Manual

5062

Print is too dark  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Print is too light  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Random marks  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-33
Repeating defects  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Shadow images   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Skew  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Solid color or black pages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Toner rubs off  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Transparency print quality is poor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Uneven print density  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-39
Vertical banding   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Vertical lines  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40

User messages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

User prompts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
User attendance messages (0–99)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-43

Service errors   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50

Printer hardware errors (100–199)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50
Firmware and/or system electronics (900–999)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-52

Symptoms   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

Symptom table—base printer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
Symptom table—500-sheet tray input option   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
Symptom table—2000-Sheet High Capacity Feeder input option   . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

Service checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-57

110.xx—Printhead error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-57
120.xx—Motor (fuser) error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58
121.xx—Fuser error service check    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60
125.xx/145.xx—ITU error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62
126.xx—LVPS error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-63
133.xx—Cartridge sensor error service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-64
141.xx—Black cartridge motor error service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66
142.xx—Cyan cartridge motor error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-67
143.xx—Magenta cartridge motor error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69
144.xx—Yellow cartridge motor error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
146.xx—Autocomp (tray 1) motor error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-72
147.xx—Staging motor error service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 2-73
149.xx—Paper path redrive motor error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-74
150.xx—Duplex motor error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-74
151.xx—ITU motor error service check   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-76
171.xx—Main fan error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-77
172.xx—LVPS fan error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-77
173.xx—Blower fan error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78
200.02—Paper Jam error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79
200.03, 200.08—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80
200.05, 200.07—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-81
200.32—Paper Jam error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82
200.33, 200.38—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84
200.35, 200.37—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-85
200.42—Paper Jam error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-87
200.43, 200.48—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-88
200.45, 200.47—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-89
201.03, 201.05, 201.07, 201.08—Paper Jam error service check  . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-90
202.32—Paper Jam error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92
241.02—Paper Jam error service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93
242.01, 243.01, 244.01, 245.01 —Paper Jam (550-sheet/2000-sheet input option) service check  . . 2-94

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

Oki Okipage8z Limited Warranty preview
Okipage8z
Brand: Oki Pages: 16
Olivetti PR2 plus Service Manual preview
PR2 plus
Brand: Olivetti Pages: 179
Olivetti JS-505 Service Manual preview
JS-505
Brand: Olivetti Pages: 36
Oki B6200 Series Maintenance Manual preview
B6200 Series
Brand: Oki Pages: 679
Oki PRO511DW Manual preview
PRO511DW
Brand: Oki Pages: 40
OKIDATA Pacemark 3410 Service Handbook preview
Pacemark 3410
Brand: OKIDATA Pages: 308
OKIDATA Pacemark 3410 Instruction Manual preview
Pacemark 3410
Brand: OKIDATA Pages: 9
OKIDATA MICROLINE 320 Quick Manual preview
MICROLINE 320
Brand: OKIDATA Pages: 2
Oki Microline 8480 FB Setup Manual preview
Microline 8480 FB
Brand: Oki Pages: 12
Canon MG7700 series Getting Started preview
MG7700 series
Brand: Canon Pages: 2
Canon PIXMA TS5300 Series Getting Started preview
PIXMA TS5300 Series
Brand: Canon Pages: 16
Canon Pixma TR7600 Series Getting Started preview
Pixma TR7600 Series
Brand: Canon Pages: 12
Canon PIXMA MX420 Series Network Setup Troubleshooting preview
PIXMA MX420 Series
Brand: Canon Pages: 34
Canon PIXMA MX700 Series Cleaning Manual preview
PIXMA MX700 Series
Brand: Canon Pages: 7
Canon TS9500 Series Getting Started preview
TS9500 Series
Brand: Canon Pages: 44
Canon PIXMA MG3220 series Setup Manual preview
PIXMA MG3220 series
Brand: Canon Pages: 5
Canon iR2016 Series User Manual preview
iR2016 Series
Brand: Canon Pages: 92
Canon PIXMA TS6200 Series Getting Started preview
PIXMA TS6200 Series
Brand: Canon Pages: 100

Brands by name

Popular brands

Load more brands