manualshive.com logo in svg

Lexmark C792de, Service Manual

The Lexmark C792de is a high-quality color laser printer perfect for any office setting. For troubleshooting and maintenance, download the free Service Manual from our website. This comprehensive manual will guide you through any technical issues, ensuring your printer stays running smoothly. Download it now from manualshive.com.

Share
Download
background image

Table of contents

xi

5062

Finisher or stacker top cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-267
Finisher stapler unit assembly removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-268

Horizontal transport unit (HTU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-269

HTU access door removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-269
HTU access door paper jam beacon (with cover and cable) removal  . . . . . . . . . . . . . . . . . . . . . . .  4-270
HTU access door rollers removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-271
HTU bin diverter gate spring removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-271
HTU bin media exit spring removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-273
HTU card (bin-full receive card and lens) removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-273
HTU card (bin-full send card and lens) removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-275
HTU controller card removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-276
HTU drive belt removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-277
HTU drive gear spring removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-277
HTU engagement roller removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-278
HTU exit roller removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-279
HTU front redrive cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-279
HTU front standard bin cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-280
HTU locking lever removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-281
HTU locking lever card removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-282
HTU lower redrive guide removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-283
HTU option hook removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-284
HTU option roller removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-287
HTU output bin removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-289
HTU output bin extension removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-289
HTU output bin solenoid removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-290
HTU output bin wire stop removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-291
HTU output option guide removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-292
HTU output option solenoid removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-292
HTU output sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-293
HTU outer front cover removal (AIO only)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-294
HTU rear redrive cover removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-294
HTU rear standard bin cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-296
HTU right bottom cover removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-299
HTU right inner cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-300
HTU sensor (access door interlock) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-304
HTU sensor (empty bin) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-305
HTU sensor (input) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-306
HTU sensor (output option position) removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-307
HTU sensor (second) removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-308
HTU sensor cable (bin-full send and receive) removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-308
HTU stopper diverter removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-309
HTU timing belts (rear) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-310
HTU to printer cable removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-310
HTU top redrive cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-311
HTU top right cover removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-312
HTU transport gear removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-313
HTU transport motor removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-314
HTU upper exit shaft removal   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-314
HTU upper guide removal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-315

Connector locations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

5-1

Locations   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1

System board cabling reference   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

Fenix Imvico TK41 Operation Manual preview
TK41
Brand: Fenix Imvico Pages: 88
Canon RP10 User Manual preview
RP10
Brand: Canon Pages: 37
Xerox Phaser 6180MFP Installation Manual preview
Phaser 6180MFP
Brand: Xerox Pages: 2
Xerox Phaser 6180MFP Features Setup Manual preview
Phaser 6180MFP
Brand: Xerox Pages: 103
Xerox Phaser 6125 Specification preview
Phaser 6125
Brand: Xerox Pages: 2
Xerox DocuPrint 4850 NPS Troubleshooting Manual preview
DocuPrint 4850 NPS
Brand: Xerox Pages: 68
Xerox DocuColor 7002 Quick Start Manual preview
DocuColor 7002
Brand: Xerox Pages: 28
Xerox DocuColor 5000AP User Manual preview
DocuColor 5000AP
Brand: Xerox Pages: 5
Xerox Document WorkCentre 450c User Manual preview
Document WorkCentre 450c
Brand: Xerox Pages: 214
Xerox DocuColor 5750 System Administration Manual preview
DocuColor 5750
Brand: Xerox Pages: 68
Xerox DocuColor 1632 Quick Connect Manual preview
DocuColor 1632
Brand: Xerox Pages: 2
Xerox PHASER 6140 User Manual preview
PHASER 6140
Brand: Xerox Pages: 170
Xerox Phaser 5500 series Setup Manual preview
Phaser 5500 series
Brand: Xerox Pages: 2
Xerox PHASER 6121MFP User Manual preview
PHASER 6121MFP
Brand: Xerox Pages: 238
Xerox DOCUCOLOR 12 Getting To Know Manual preview
DOCUCOLOR 12
Brand: Xerox Pages: 24
Xerox DOCUCOLOR 12 Supplement Manual preview
DOCUCOLOR 12
Brand: Xerox Pages: 18
Xerox DocuColor 240 Evaluator Manual preview
DocuColor 240
Brand: Xerox Pages: 18
Xerox Phaser 3600 Installation Manual preview
Phaser 3600
Brand: Xerox Pages: 2

Brands by name

Popular brands

Load more brands