Lexmark C792de Service Manual Download Page 94

Page: 94 / 630

2-56

Service Manual

5062

Symptoms

Symptom table—base printer

Symptom table—500-sheet tray input option

Symptom table—2000-Sheet High Capacity Feeder input option

Symptom

Action

Dead printer

Go to

“Dead printer service check” on page 2-117

Tray linking will not work.

Go to

“Tray linking service check” on page 2-139

Paper pick mechanism—pick arm is stuck
in the down position

Go to

“Pick arm stuck down service check” on page 2-132

Symptom

Action

Printer fails to recognize the option is installed.

Go to

“Input option not detected (550-sheet/2000-

sheet input option) service check” on page 2-120

Printer keeps on prompting that the jam door is open
even if it’s close.

Go to

“Jam clearance cover open (550-sheet/2000-

sheet input option) service check” on page 2-123

Tray X does not recognize the media size loaded.

Go to

“Media size error (550-sheet/2000-sheet

input option) service check.” on page 2-125

Tray missing message appears even if media tray is
installed.

Media tray won’t fit the drawer.

Go to

“Media tray missing (550-sheet input option)

service check” on page 2-126

Double feed

Go to

“Double feed (550-sheet/2000-sheet input

option) service check” on page 2-118

Printout is skewed.

Go to

“Skew (550-sheet input option) service

check” on page 2-134

Tray LED won’t light up during paper jam or tray
empty.

Go to

“Tray jam indicator (550-sheet/2000-sheet

input option) service check” on page 2-139

Symptom

Action

Printer fails to recognize the option is installed.

Go to

“Input option not detected (550-sheet/2000-

sheet input option) service check” on page 2-120

Printer keeps on prompting that the jam door is open
even if it’s close.

Go to

“Jam clearance cover open (550-sheet/2000-

sheet input option) service check” on page 2-123

Tray X does not recognize the media size loaded.

Go to

“Media size error (550-sheet/2000-sheet

input option) service check.” on page 2-125

Tray missing message appears even if media tray is
installed.

Go to

“Media tray missing (2000-sheet input

option) service check” on page 2-127

Double feed

Go to

“Double feed (550-sheet/2000-sheet input

option) service check” on page 2-118

Printout is skewed.

Go to

“Skew (2000-sheet input option) service

check” on page 2-135

Printer prompts that tray is empty even if there’s
paper in the tray.

Go to

“Tray empty (2000-sheet input option)

service check” on page 2-137

Tray LED won’t light up during paper jam or tray
empty.

Go to

“Tray jam indicator (550-sheet/2000-sheet

input option) service check” on page 2-139

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for C792de

Reviews:

Related manuals for C792de

Brands by name

Popular brands

Lexmark C792de, Service Manual

Search results

Summary of Contents for C792de

Reviews:

Related manuals for C792de

Brands by name

Popular brands