Lexmark C792de Service Manual Download Page 184 | Manualshive

Page: 184 / 630

background image

3-6

Service Manual

5062

Accessing service menus

There are different test menus that can be accessed during POR to identify problems with the printer.

Diagnostics menu

1. Turn off the printer.
2. Press and hold 3 and 6.

3. Turn on the printer.
4. Release the buttons when the splash screen

appears.

The Diagnostics menu group
contains the settings and
operations used while
manufacturing and servicing the
printer.

For more information, see

“Diagnostics menu” on
page 3-7

Configuration menu

1. Turn off the printer.
2. Press and hold 2 and 6.

3. Turn on the printer.
4. Release the buttons when the splash screen

appears.

The Configuration menu group
contains a set of menus, settings,
and operations which are
infrequently required by a user.
Generally, the options made
available in this menu group are
used to configure a printer for
operation.

See

“Configuration Menu” on

for more information.

Network SE menu

While in Network/Ports Menu, press and hold 9, 7,
and 6.

SE menu

From a browser, add “/se” to the device IP address
(for example: http://158.183.3.2/se)

«
...
182
183
184
185
186
...
»

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

Brand: NCR Pages: 2

Brand: Samsung Pages: 9

Bixolon SRP-500

Brand: Samsung Pages: 27

550N - CLP Color Laser Printer

Brand: Samsung Pages: 288

2 COLOR THERMAL PRINTER SRP-275

Brand: Samsung Pages: 8

Brand: Samsung Pages: 6

Brand: Samsung Pages: 91

Brand: GE Pages: 16

Brand: Star Micronics Pages: 24

Daisy Wheel 410

Brand: Radio Shack Pages: 140

Brand: Lexmark Pages: 289

Brand: Citizen Pages: 37

Brand: Konica Minolta Pages: 4

8860MFPD - Multifunction Inkjet Printer

Brand: Xerox Pages: 16

giant 100 series

Brand: Sam4s Pages: 54

Brand: Lexmark Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands