Lenovo ThinkSystem ST550 Setup Manual Download Page 18

Page: 18 / 136

Functions

Offerings

Functions

Multi-
system
mgmt

OS
deploy-
ment

System
configu-
ration

Firm-
ware
up-
dates

Event-
s/alert
moni-
toring

Inven-
tory/
logs

Pow-
er
mgmt

Power
planning

Lenovo XClarity Controller

√

Lenovo XClarity
Administrator

√

Lenovo
XClarity
Essen-
tials
toolset

OneCLI

√

Bootable Media

Creator

√

UpdateXpress

√

Lenovo XClarity Provisioning
Manager

√

Lenovo XClarity Integrator

√

Lenovo XClarity Energy
Manager

√

Lenovo Capacity Planner

√

Notes:

1. Most options can be updated through the Lenovo tools. Some options, such as GPU firmware or Omni-

Path firmware, require the use of vendor tools.

2. Firmware updates are limited to Lenovo XClarity Provisioning Manager, BMC firmware, and UEFI

updates only. Firmware updates for optional devices, such as adapters, are not supported.

3. The server UEFI settings for option ROM must be set to

UEFI

to update firmware using Lenovo XClarity

Essentials Bootable Media Creator.

4. The server UEFI settings for option ROM must be set to

UEFI

for detailed adapter card information, such

as model name and firmware levels, to be displayed in Lenovo XClarity Administrator, Lenovo XClarity
Controller, or Lenovo XClarity Essentials OneCLI.

5. It’s highly recommended that you check the power summary data for your server using Lenovo Capacity

Planner before purchasing any new parts.

ThinkSystem ST550 Setup Guide

Summary of Contents for ThinkSystem ST550









































































































































Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands

Lenovo ThinkSystem ST550, Setup Manual

Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands