Lenovo ThinkSystem ST550 Setup Manual Download Page 16 | Manualshive

Page: 16 / 136

background image

• Fan 4 is installed.

• Two hot-swap power supplies are installed.

• NVMe SSD is not installed.

• Graphics adapters are not installed.

• SAS drives with capacity larger than or equal to 2 TB are not installed in the expansion drive cage.

• Processors with TDP more than 125 watts are not installed.

Important information about EU ecodesign requirements

The following are EU ecodesign requirements for ErP Lot 9 products:

• Minimum memory should be 16 GB.

• Delta or Acbel 450-watt power supplies should not be picked.

• Processors should not picked for one-processor configurations: Intel Xeon 3104, 3106, 3204, 4108, 4112,

5122, 5222, 8156, and 8256

Management options

The XClarity portfolio and other system management offerings described in this section are available to help
you manage the servers more conveniently and efficiently.

Overview

Offerings

Description

Lenovo XClarity Controller

Baseboard management controller.

Consolidates the service processor functionality, Super I/O, video controller, and
remote presence capabilities into a single chip on the server system board.

Interface

• CLI application

• GUI application

• Mobile application

• Web interface

• REST API

Usage and downloads

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.systems.management.xcc.doc/
product_page.html

Lenovo XClarity Administrator

Centralized interface for multi-server management.

Interface

• GUI application

• Mobile application

• Web interface

• REST API

Usage and downloads

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxca.doc/aug_product_page.html

12

ThinkSystem ST550 Setup Guide

«
...
14
15
16
17
18
...
»

Summary of Contents for ThinkSystem ST550









































































































































Reviews:

No comments

Related manuals for ThinkSystem ST550

ShareCenter DNS-343

Brand: D-Link Pages: 12

Power 750 Express

Brand: IBM Pages: 86

Brand: Yeong Yang Pages: 7

Brand: Devolinx Pages: 51

Brand: NEC Pages: 408

Brand: AXIOMTEK Pages: 55

Brand: Avaya Pages: 119

Brand: Portwell Pages: 21

Brand: Crestron Pages: 2

Brand: Olive Pages: 103

Brand: Eneo Pages: 94

PLATINUM 1500 IR M5

Brand: MAXDATA Pages: 44

Brand: Stratus Pages: 106

Brand: Data-Tronix Pages: 29

Brand: Data-Tronix Pages: 30

Brand: Bodet Pages: 13

Brand: XtendLan Pages: 27

Brand: Black Box Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands