Lenovo ThinkSystem ST550 Setup Manual Download Page 44

Page: 44 / 136

Server models with twenty 2.5-inch hot-swap drives

Use this section to understand the cable routing for server models with twenty 2.5-inch hot-swap drives.

Server model: twenty 2.5-inch SAS/SATA drives, one 24i RAID adapter

Notes:

• Ensure that all cables are routed through the correct cable clips.

• Broken lines indicate the hidden parts.

Figure 21. Cable routing for server models with twenty 2.5-inch SAS/SATA drives and one 24i RAID adapter

Cable

From

SAS signal cable for

backplane 1

SAS 0 and SAS 1 connectors on
backplane 1

C0 and C1 connectors on the 24i RAID
adapter

Power cable for backplane 1

Power connector on backplane 1

Backplane 1 power connector on the
system board

SAS signal cable for

backplane 2

SAS 0 and SAS 1 connectors on
backplane 2

C2 and C3 connectors on the 24i RAID
adapter

ThinkSystem ST550 Setup Guide

Summary of Contents for ThinkSystem ST550









































































































































Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands

Lenovo ThinkSystem ST550, Setup Manual

Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands