Lenovo ThinkSystem ST550 Setup Manual Download Page 106 | Manualshive

Page: 106 / 136

background image

Step 1. Touch the static-protective package that contains the new RAID super capacitor module to any

unpainted surface on the outside of the server. Then, take the new RAID super capacitor module
out of the package and place it on a static-protective surface.

Step 2. Insert one end of the RAID super capacitor module into the slot of the air baffle. Then, press down

the other end of the RAID super capacitor module until it snaps in place.

Figure 64. RAID super capacitor module installation

Step 3. Connect the RAID super capacitor module to the extension cable.

Install the server cover

Use this information to install the server cover.

Guidelines” on

this task” on

Static Sensitive Device

Ground package before opening”

S033

CAUTION:
Hazardous energy present. Voltages with hazardous energy might cause heating when shorted with
metal, which might result in spattered metal, burns, or both.

102

ThinkSystem ST550 Setup Guide

«
...
104
105
106
107
108
...
»

Summary of Contents for ThinkSystem ST550









































































































































Reviews:

No comments

Related manuals for ThinkSystem ST550

Brand: IBM Pages: 54

Brand: Oki Pages: 4

Brand: Lantronix Pages: 299

Brand: Wyse Pages: 6

Brand: Sun Microsystems Pages: 148

Eternus DX80 S2

Brand: Fujitsu Pages: 186

Brand: Fujitsu Pages: 242

Brand: Kontron Embedded Computers Pages: 46

Sooloos Ensemble

Brand: Meridian Pages: 2

Brand: MRV Communications Pages: 65

Brand: Axis Pages: 129

Brand: Black Box Pages: 60

Brand: BushkaBlue Pages: 30

Brand: Mirapoint Pages: 76

Brand: DEVA Pages: 90

Brand: 3onedata Pages: 3

Brand: Vlinx Pages: 43

Brand: Interlink network Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands